Siemens 6GK1411-1AC00 Operating Instructions Manual Download Page 23

Page: 23 / 150

SIMATIC CC7
Operating Instructions, 10/2019, C79000-G8976-C503-02

LEDs, Connectors, Buttons, CLP

2.1

LEDs

The LEDs on the front show the states of the module.
The LED symbols in the table below correspond to the following states of the LEDs:

LED symbol

LED status

OFF

ON (steady light) *

Flashing

* : Part flashes yellow and part lit green

Meaning of the LED displays

LED name

(colors)

LED pattern Meaning / Module status

Power
(green)

Power supply

Power OFF

Power ON

Device Connection
(green / yellow)

Connection to process stations

No connection to configured process stations

Existing connection to all configured process stations

No connection to at least one of the configured process stations

No communication with process stations Possible causes:

•

Incorrect configuration

•

Stop of communication via:
–

WBM: "Maintenance > Communication / Restart"

–

CC716: Digital input

No process station configured

Summary of Contents for 6GK1411-1AC00























































































































































Search results

Summary of Contents for 6GK1411-1AC00

Reviews:

Related manuals for 6GK1411-1AC00

Brands by name

Popular brands

Siemens 6GK1411-1AC00, Operating Instructions Manual

Search results

Summary of Contents for 6GK1411-1AC00

Reviews:

Related manuals for 6GK1411-1AC00

Brands by name

Popular brands