background image

Technical data 

 

 

 

SIMATIC MV320 / SIMATIC MV325 

48

 

Operating Instructions, 08/2015, C79000-G8976-C352-03 

 

6GF3325-0HT01 

Optical resolution 

 

 

Near field 

960 x 640 

 

Wide field 

960 x 640 

Roll angle 

±60° (from front to rear) 

Angle of inclination 

± 60° level parallel to symbol (from side to side) 

Rotational tolerance 

± 180° 

Print contrast resolution 

25% (1D codes) or 35% (2D codes) absolute 

dark/light reflectance differential measured at 

650 nm 

Target beam 

Single, blue target strip 

Number of scanning operations 

Up to 50 000 scans/charge  

Read distances 

The read distances are made up of a wide field and a near field. 

 

All code patterns must be of high quality and on a physical midline at an angle of 10° 

when read. 

 

The table refers to the AGC factory settings; accuracy: ± 10 % 

Table 9- 1 

Read distances 

Test code 

Min. mm 

Max. mm  

3 mil Code 39 

80 

102 

7.5 mil Code 39 

33 

182 

10.5 mil GS1 DataBar 

20 

220 

13 mil UPC 

28 

280 

4.2 mil Data Matrix 

48 

110 

5 mil Data Matrix 

43 

115 

6.3 mil Data Matrix 

33 

150 

10 mil Data Matrix 

20 

180 

20.8 mil Data Matrix 

28 

343 

 1 mil = 0.0254 mm 

The ideal read distance is about 100 mm. Depending on the code type and code size, 

smaller or larger distances are possible. 

Summary of Contents for 6GF3320-0HT01

































































Reviews: