Siemens 6GF3320-0HT01 Operating Instructions Manual Download

Page: 39 / 64

SIMATIC MV320 / SIMATIC MV325
Operating Instructions, 08/2015, C79000-G8976-C352-03

Alarm, error and system messages

7.1

Feedback from the reader

Table 7- 1

SIMATIC MV320

Situation

LED displays on the

reader

Acoustic signal Vibration signal

SIMATIC MV320 is turned on.

Green LED flashes

Successful establishment of the con-

nection between SIMATIC MV320 and

the host (by cable).

Green LED goes off

after connection

establishment

Decoding attempt active.

Green LED is off

Decoding and data transfer successful. Green LED flashes

Configuration code successfully

decoded and processed.

Green LED flashes

Configuration code successfully

decoded but not successfully

processed.

Green LED flashes

Table 7- 2

SIMATIC MV325

Situation

LED displays on the

reader

Acoustic signal Vibration signal

SIMATIC MV325 turned on

successfully.

All LEDs flash

SIMATIC MV325 connected to host

successfully.

Wireless symbol

flashes

SIMATIC MV325 not connected to host

successfully.

Decoding and data transfer successful. Read display flashes

Decoding and data transfer not

successful.

Configuration code successfully

decoded and processed.

Read display flashes

Configuration code not successfully

decoded and processed.

Batch mode enabled and no data

stored

Batch symbol off

Batch mode enabled and data stored. Batch symbol flash-

ing

Summary of Contents for 6GF3320-0HT01

































































Search results

Summary of Contents for 6GF3320-0HT01

Reviews:

Related manuals for 6GF3320-0HT01

Brands by name

Popular brands

Siemens 6GF3320-0HT01, Operating Instructions Manual

Search results

Summary of Contents for 6GF3320-0HT01

Reviews:

Related manuals for 6GF3320-0HT01

Brands by name

Popular brands