manualshive.com logo in svg

Siemens 6EP1437-3BA10, Manual, Page: 40 / 58

Share
Download
Siemens 6EP1437-3BA10 Manual Download Page 40

Safety, approvals, EMC 

 

7.2 Test voltage 

 

SITOP PSU8200 3ph 

40

 

Manual, 11.2014, C98130-A7638-A1-2-7629 

7.2

 

Test voltage 

 

Figure 7-1 

Test voltage diagram 

Only the manufacturer can perform the type test and production test; users can also perform 

the field test. 
Preconditions for performing the field test: 
Tests (A) & (B) 

●

 

Connect the input terminals with one another 

●

 

Connect the output terminals, signaling contact and PE with one another 

Test (C) 

●

 

Connect the output terminals and signaling contact with one another and measure with 

respect to PE 

Table 7- 1 

Test voltage for 6EP3436-8SB00-0AY0 

 

Test time 

Prim ↔ sec (A)

 

Prim ↔ PE (B)

 

Sec ↔ PE (C)

 

Type test 

60 s 

4200 VDC 

2200 VDC 

700 VDC 

60 s 

3000 VAC 

1500 VAC 

500 VAC 

Production test 

1 s 

4200 VDC 

4200 VDC 

500 VDC 

1 s 

3000 VAC 

3000 VAC 

350 VAC 

Field test 

1 s 

2200 VDC 

2200 VDC 

500 VDC 

1 s 

1500 VAC 

1500 VAC 

350 VAC 

 Note: 

Tripping current for DC measurement: 0 mA 

Tripping current for AC measurement: <100 mA 

 

Summary of Contents for 6EP1437-3BA10



























































Reviews:

No comments