Siemens 6DL1131-6TH00-0PH1 Equipment Manual Download | Manualshive

Page: 7 / 50

background image

Preface

2

Validity of the documentation

This device manual describes the DI 16×NAMUR HA I/O module with the article number
6DL1131-6TH00-0PH11.

It complements the system manual of the ET 200SP HA Distributed I/O System.

Functions that generally relate to the system are described in this manual.

The information in this device manual and the system/function manuals enables you to put the
ET 200SP HA into operation.

Conventions

Please also observe notes marked as follows:

Note

A note contains important information on the product described in the documentation, on the
handling of the product and on the section of the documentation to which particular attention
should be paid.

DI 16xNAMUR HA
Equipment Manual, 08/2019, A5E39293880-AD

7

«
...
5
6
7
8
9
...
»

Summary of Contents for 6DL1131-6TH00-0PH1



















































Reviews:

No comments

Related manuals for 6DL1131-6TH00-0PH1

Brand: Mitsubishi Electric Pages: 107

Brand: Mitsubishi Electric Pages: 56

Brand: Mitsubishi Electric Pages: 36

Brand: Mitsubishi Electric Pages: 9

Brand: Mitsubishi Electric Pages: 64

Brand: Mitsubishi Electric Pages: 2

Brand: Mitsubishi Electric Pages: 22

IMSE UltraBase40

Brand: Abelko Pages: 4

Brand: Eaton Pages: 12

Brand: Topgreener Pages: 2

Brand: Areva Pages: 32

Brand: Areva Pages: 100

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands