Siemens 6DL1131-6TH00-0PH1 Equipment Manual Download | Manualshive

Page: 13 / 50

background image

• Reference identification label

• Shield connector

• Terminal blocks

4.3

Terminal blocks

Definition

The terminal blocks provide the process terminals (push-in terminals) for components such as
devices to be connected.

Description

The following terminal blocks are available for the I/O module:

Article number

Color

Description

6DL1193-6TP00-0DH1 Lit

6DL1193-6TP00-0BH1

Dark

6DL1193-6TP00-0DM1 Lit

For redundant configuration

6DL1193-6TP00-0BM1 Dark

For redundant configuration

6DL1193-6TP00-0DN0 Lit

With additional potential distributors for ground connection of the actuators

6DL1193-6TP00-0BN0

Dark

With additional potential distributors for ground connection of the actuators

Note

Terminal blocks are not included in the scope of delivery of the I/O module and must be ordered
separately.

You can find additional information on the configuration in the system manual.

Product overview

4.3 Terminal blocks

DI 16xNAMUR HA
Equipment Manual, 08/2019, A5E39293880-AD

13

«
...
11
12
13
14
15
...
»

Summary of Contents for 6DL1131-6TH00-0PH1



















































Reviews:

No comments

Related manuals for 6DL1131-6TH00-0PH1

Brand: IFM Pages: 7

EPSITRON 787-1668 Series

Brand: WAGO Pages: 48

Brand: GE Pages: 260

Brand: Eaton Pages: 38

Brand: GE Pages: 32

Brand: GE Pages: 40

Brand: GE Pages: 45

Brand: GE Pages: 70

Brand: GE Pages: 31

Brand: Eaton Pages: 12

Brand: Eaton Pages: 34

Brand: Iso-Tech Pages: 71

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands