Siemens 3VA1 100 A Manual Download Page 194

Page: 194 / 532

Accessories

4.3 Connection system

3VA molded case circuit breakers

194

Manual, 04/2015, A5E03603177010-02

Terminal cover
The terminal cover is compatible with:

●

Box terminals

●

Circular conductor terminals

●

Lug terminals

The terminal cover is simply snapped into place on 3VA1 breakers, or is snapped into place

and secured with 2 screws on 3VA2 breakers.

Extended terminal cover
The extended terminal cover always consists of two parts:

①

Rear insulating plate, provides insulation from the cubicle mounting plate

②

Front half, pushed over the molded case circuit breaker from the front

The insulating plate is fitted to the rear panel of the molded case circuit breaker and then

secured by 2 screws to the front half of the terminal cover. The extended terminal cover is

also secured by 2 additional screws to the molded case circuit breaker itself.
The extended terminal cover is compatible with:

●

Circular conductor terminals, large (extended terminal cover included in scope of supply)

●

Circular conductor terminals, 2 cables (extended terminal cover included in scope of

supply)

●

Circular conductor terminals, 6 cables (extended terminal cover included in scope of

supply)

●

Front connection bars extended

●

Front connection bars edgewise

Summary of Contents for 3VA1 100 A





















































































































































































































































































































































































































































































































































Search results

Summary of Contents for 3VA1 100 A

Reviews:

Brands by name

Popular brands

Siemens 3VA1 100 A, Manual

Search results

Summary of Contents for 3VA1 100 A

Reviews:

Brands by name

Popular brands