Siemens 3RB24 Manual Download Page 20 | Manualshive

Page: 20 / 128

Siemens 3RB24 Manual Download Page 20

3.2

System structure

Device concept

The 3RB24 solid-state overload relay has a modular device concept. Each device consists of a
motor-current-independent evaluation module, and a motor-current-dependent current
measuring module. Both modules are connected electrically to each other by connecting cable
via the interface.

Optionally, the 3RA6935‑0A operator panel can be connected to the front of the evaluation
module.

Requirements

You require the following tools for system setup:

• 1 x evaluation module 3RB2483‑4A .1

• 1 x current measuring module 3RB29.6‑2...

• 1 x connecting cable 3RB2987‑2.

Note

The connecting cable 3RB2987‑2B for linking the evaluation module and the current
measuring module is only to be used when the evaluation module is mounted direct on the
current measuring module.

System structure

The following graphic illustrates the design principle of a system.

. .

.

3

1

2

①

Evaluation module 3RB2483‑4A .1

②

Current measuring module 3RB29.6‑2...

③

Connecting cable 3RB2987‑2.

Figure 3-1

System structure

Product description
3.2 System structure

SIRIUS 3RB24 electronic overload relay for IO-Link

20

Equipment Manual, 07/2022, NEB969165602000/RS-AA/003

«
...
18
19
20
21
22
...
»

Summary of Contents for 3RB24

































































































































Reviews:

No comments