manualshive.com logo in svg

Siemens 1PQ8, Operating Instructions & Installation Instructions

Share
Download
Siemens 1PQ8 Operating Instructions & Installation Instructions Download Page 44

NOTICE
High temperatures 
The motor components get very hot during operation. High temperatures can damage 

mounting parts such as the cable insulation. 
● Temperature-sensitive parts such as normal cables or electronic components must not 

rest against or be attached to mounted machine parts.

● Only use heat-resistant mounting parts. The connecting cables and cable entries must be 

suitable for the ambient temperature.

5.1.2

Insulation resistance and polarization index

Measuring the insulation resistance and polarization index (PI) provides information on the 

condition of the machine. It is therefore important to check the insulation resistance and the 

polarization index at the following times:     
● Before starting up a machine for the first time
● After an extended period in storage or downtime
● Within the scope of maintenance work
The following information is provided regarding the state of the winding insulation:
● Is the winding head insulation conductively contaminated?
● Has the winding insulation absorbed moisture?
As such, you can determine whether the machine needs commissioning or any necessary 

measures such as cleaning and/or drying the winding:
● Can the machine be put into operation?
● Must the windings be cleaned or dried?
Detailed information on testing and the limit values can be found here:
"Testing the insulation resistance and polarization index"  (Page 45) 

Assembly
5.1 Preparations for installation

SIMOTICS TN Series N-compact  1LH8

44

Operating Instructions 06/2017

Summary of Contents for 1PQ8













































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands