manualshive.com logo in svg

Siemens 1PQ8, Operating Instructions & Installation Instructions

Share
Download
Siemens 1PQ8 Operating Instructions & Installation Instructions Download Page 33

4.14.5

Transporting the machine set

WARNING

Falling down of the machine
The lifting lugs on the machine are designed only for the weight of the machine. If a machine 

set is lifted and transported on a single machine, this can lead to mechanical failure of the 

lifting lug. The machine or machine set may fall. This can result in death, serious injury or 

material damage.
● Do not lift machine sets by attaching lifting tackle to the individual machines.
● Use only the equipment provided, e.g. the openings or lugs on the base plates, for 

transporting machine sets. Note the maximum capacity of the lifting lug.

Note
Place the machine in a secure and raised position
In order to obtain easy and safe access to the underside of the machine, place it in a secure 

and raised position.

DANGER

Standing under suspended loads
If the lifting gear or load handling attachments were to fail, the machine could fall. This can 

result in death, serious injury or material damage. 
● Never remain under or in the immediate vicinity of the machine when it is raised.

4.14.6

Storage

You must correctly store the machine if you do not install and use it after it has been delivered. 

NOTICE
Bearing seizure damage if incorrectly stored
If storage conditions are inappropriate there is a risk of bearing seizure damage. Resulting 

damage can include scoring (brinelling) and corrosion. 
● Follow the storage guidelines.

Preconditions and preparations

● Only store goods in undamaged packaging. Unpack the goods if the packaging is damaged. 

Correctly store the goods corresponding to the type.

● Repair any damage to the packaging before putting the equipment into storage insofar as 

this is necessary to ensure proper storage conditions.

Preparations for use

4.14 Transport and storage

SIMOTICS TN Series N-compact  1LH8

Operating Instructions 06/2017

33

Summary of Contents for 1PQ8













































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands