Siemens 1PH818 Operating Instructions & Installation Instructions Download Page 99

Page: 99 / 198

8.10.5

Rolling-contact bearing faults

Note
Damage to roller bearings can be difficult to detect in some cases. If in doubt, replace the roller

bearing. Contact the Service Center.

Table 8-4

Roller bearing faults

↓ Bearing overheats

↓ Bearing "whistles"

↓ Bearing "knocks"

Possible causes of fault

Remedial measures

High coupling pressure

Align the machine more accurately.

Ambient temperature higher than 40 °C

Use high-temperature grease.

Insufficient lubrication

Grease the bearings as instructed.

Too much grease in bearing

Remove surplus grease. Contact the Service Center, if necessary.

Wrong grease in the bearing

Use the correct grease.

Belt tension too high *

Reduce the drive belt tension.

Bearing contaminated

Contact the Service Center.

Bearing canted

Insufficient bearing play

Bearing corroded

X Friction marks on raceway

X Scoring (brinelling)

X Excessive bearing play

X Mechanical wear of bearing elements

* Only in special version

8.10.6

Holding brake faults

Information on holding brake faults can be found in the manufacturer's operating instructions

in the (Page 139) appendix.

Operation

8.10 Faults

SIMOTICS M-1PH8 1PH818., 1PH822.

Operating Instructions 07/2016

Summary of Contents for 1PH818







































































































































































































Search results

Summary of Contents for 1PH818

Reviews:

Brands by name

Popular brands

Siemens 1PH818, Operating Instructions & Installation Instructions

Search results

Summary of Contents for 1PH818

Reviews:

Brands by name

Popular brands