Siemens 1PH818 Operating Instructions & Installation Instructions Download Page 88 | Manualshive

Page: 88 / 198

background image

7.5

Switching on

● See the operating instructions of the frequency converter for switching on.
● Before you switch on the motor, ensure that the parameters of the frequency converter

have been assigned correctly.

● Use appropriate commissioning tools, such as "Drive ES" or "STARTER".

NOTICE
Operation noise or abnormal noises
The motor can be damaged by improper handling during transport, storage or set up. If a

damaged motor is operated damage to the winding, bearings or, complete destruction of

the motor can be the result.
If the motor is not running smoothly or is emitting abnormal noises, de-energize it, and

determine the cause of the fault as the motor runs down.

Maximum speed
The maximum rotational speed n

max

is the highest permissible operating speed. The maximum

rotational speed is specified on the rating plate.

See also

Description (Page 21)

7.6

Test run

After installation or inspection, carry out a test run:
1. Switch on the cooling systems.
2. Start up the machine without a load. To do this, close the circuit breaker and do not switch

off prematurely. Check whether it is running smoothly.

Switching the machine off again while it is starting up and still running at slow speed should

be kept to a bare minimum, for example for checking the direction of rotation or for checking

in general.

Allow the machine to run down before switching it on again.

3. If it runs perfectly, connect a load.

Commissioning
7.6 Test run

SIMOTICS M-1PH8 1PH818., 1PH822.

88

Operating Instructions 07/2016

«
...
86
87
88
89
90
...
»

Summary of Contents for 1PH818







































































































































































































Reviews:

No comments

Related manuals for 1PH818

Brand: Quectel Pages: 71

Brand: AL-KO Pages: 182

Cobalt IP Analog

Brand: DCCconcepts Pages: 2

Brand: Sumoto Pages: 20

Brand: Kohler Pages: 4

Brand: nord Pages: 91

Brand: Briggs & Stratton Pages: 6

Lombardini LGW 523 MPI

Brand: Kohler Pages: 144

Brand: Himax Pages: 2

AG2210-LP Series

Brand: Beckhoff Pages: 35

Brand: Volvo Penta Pages: 20

Brand: Volvo Penta Pages: 35

Brand: Volvo Penta Pages: 45

Brand: Volvo Penta Pages: 50

Brand: Volvo Penta Pages: 68

Brand: Volvo Penta Pages: 74

Brand: STG-BEIKIRCH Pages: 9

Brand: Lombardini Pages: 64

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands