Siemens 1PH818 Operating Instructions & Installation Instructions Download Page 78

Page: 78 / 198

Type

Supply voltage

Current consumption

1PH818.

1 AC 200 V … 277 V / 50 Hz, 60 Hz (± 10 %)

1.45 A ... 1.05 A

1PH822.

1 AC 200 V … 277 V / 50 Hz, 60 Hz (± 10 %)

2.3 A ... 1.6 A

6.4.3

Connecting the speed encoder

The speed encoder is connected at the terminal box using a plug connection

①

. This is located

on the terminal box enclosure.

Figure 6-4

Detailed view: Plug-in connection

Note
The plug-in connection may differ from the standard layout in the case of special orders. For

versions without speed encoder, connection thread M16x1.5 is located here.

Connecting a speed encoder via DRIVE-CLiQ

The signal connection between the motor and the converter is established via the DRIVE‑CLiQ

cable MOTION‑CONNECT.
● Always use prefabricated cables from Siemens. These cables reduce the mounting/

installation time and costs and increase operational reliability.

● Push the connector of the DRIVE‑CLiQ cable into the socket until the catch spring latches

into place. Pay attention to the coding of the connector.

Electrical connection
6.4 Auxiliary circuits

SIMOTICS M-1PH8 1PH818., 1PH822.

Operating Instructions 07/2016

Summary of Contents for 1PH818







































































































































































































Search results

Summary of Contents for 1PH818

Reviews:

Brands by name

Popular brands

Siemens 1PH818, Operating Instructions & Installation Instructions

Search results

Summary of Contents for 1PH818

Reviews:

Brands by name

Popular brands