manualshive.com logo in svg

Siemens 1PH818, Operating Instructions & Installation Instructions

Share
Download
Siemens 1PH818 Operating Instructions & Installation Instructions Download Page 54

5.2.3

Removing anti-corrosion protection

Machined, bright surfaces of machine parts and small components such as screws, bolts, 

wedges, feather keys and dowel pins, are treated with an anti-corrosion agent.
Carefully remove the anti-corrosion agent just before starting the installation work.   

Bright surfaces on machine parts

● Use petroleum, petroleum ether, or a similar solvent or detergent to remove the anti-

corrosion coating from the machined surfaces of machine parts and from small components.

NOTICE
Paintwork damage
If painted surfaces come into contact with the detergent or solvent, the paintwork can be 

damaged.

● Use a suitable solvent to soften thick layers of anti-corrosion agent. Then push the softened 

layers off using a piece of hardwood approximately 10 x 10 x 1 cm. Do not sand the 

protective coating down or scrape it off.

NOTICE
Damage to the machine surface
If you use metal objects such as scrapers, spatulas, or plates to remove the anti-corrosion 

protection, this could result in damage to the surfaces of the machine parts.

● Lightly oil the depreserved surfaces.

Mounting
5.2 Lift the machine to where it will be mounted and position it

SIMOTICS M-1PH8  1PH818., 1PH822.

54

Operating Instructions 07/2016

Summary of Contents for 1PH818







































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands