manualshive.com logo in svg

Siemens 1PH818, Operating Instructions & Installation Instructions

Share
Download
Siemens 1PH818 Operating Instructions & Installation Instructions Download Page 26

Supplementary devices 

A temperature sensor is integrated in the stator winding to monitor the winding temperature. 

The type of temperature sensor is specified on the rating plate.
Depending on the order options, various supplementary devices such as encoder systems can 

be either installed or mounted.

Holding brake   

Depending on the order, a special version of a holding brake from the Stromag  company is 

mounted. Various types of holding brake are mounted depending on the shaft height. 

NOTICE
Technical data for the special version of the holding brake
The following technical data applies to the special version of the mounted holding brake. The 

corresponding data in the manufacturers operating instructions do not apply.

Table 3-4

Technical data of the holding brake

Technical data

NFF-A 63

AH180

NFF-A 100 

AH225

Braking torque

M

Brake

[Nm]

1000

1600

Max. speed

n

Brake

[rpm]

3500

3100

Weight incl. hollow shaft

m

brake

[kg]

63

88

Moment of inertia

J

brake

[kgm

2

]

0,022

0,051

Total moment of inertia (emer‐

gency stop)

J

total

[kgm

2

]

1,3

3,9

Rated voltage

U

[V]

230 V (AC)

230 V (AC)

Permitted single switched energy P

[W]

98

210

Coil current

I

[A]

2,21

2,70

Number of emergency stops

Z

-

2100

1200

Opening time

 

[ms]

300

300

Closing time

 

[ms]

80

100

Note
More information
● Magnetic field when the brake is open (Page 84)

See also

Operating instructions, holding brake (Page 139)

Description

SIMOTICS M-1PH8  1PH818., 1PH822.

26

Operating Instructions 07/2016

Summary of Contents for 1PH818







































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands