Siemens 1PH818 Operating Instructions & Installation Instructions Download Page 118

Page: 118 / 198

WARNING

Motor-specific sensor module
The Sensor Module contains motor-specific and sensor-specific data and an electronic

nameplate.
If you operate a different Sensor Module on the motor, this can result in serious injury or

death, or cause considerable material damage.
Only operate the sensor module on the original motor. Do not install the sensor module on

other motors. Do not replace the sensor module with a sensor module from a different motor.

9.3.6

Touch up any damaged paintwork

If the paint is damaged, it must be repaired in order to protect the unit against corrosion.

Note
Paint system
Contact the Service Center (Page 131) before you repair any paint damage. They will provide

you with more information about the correct paint system and methods of repairing paint

damage.

Maintenance
9.3 Repair

SIMOTICS M-1PH8 1PH818., 1PH822.

118

Operating Instructions 07/2016

Summary of Contents for 1PH818







































































































































































































Search results

Summary of Contents for 1PH818

Reviews:

Brands by name

Popular brands

Siemens 1PH818, Operating Instructions & Installation Instructions

Search results

Summary of Contents for 1PH818

Reviews:

Brands by name

Popular brands