SIEB & MEYER 0362171DA1 Series Hardware Description Download

Page: 60 / 65

Safety circuit / restart lock (STO)

– Performance Level e

▸

according to EN 61508-1:2010 and EN 61800-5-2:2014-06
– PFH = 0
– SFF = 100 % (if there are PFH values, then SFF<100%)
– HFT = 0

The safety concept K1 meets the requirements of SIL 3 according to the standards

named above.

Requirements according to DIN EN 61800-5-2:2014-06

When connected appropriately, the safety concept K1 does not supply any share of dan-

gerous, undetected errors in the safety chain for the function STO.
Thus the stop function 0+1 according to EN 60204-1:2007-6 is realized.

10.4

Restart Lock Procedure

The following diagram shows the restart lock procedure by means of a time axis, includ-

ing the required steps that must be performed in order to be able to restart the device

after an activated restart lock.

Drive Amplifier SD2B plus - 0362171DA1xxxx, 0362171DB1xxxx

Summary of Contents for 0362171DA1 Series


































































Search results

Summary of Contents for 0362171DA1 Series

Reviews:

Related manuals for 0362171DA1 Series

Brands by name

Popular brands

SIEB & MEYER 0362171DA1 Series, Hardware Description

Search results

Summary of Contents for 0362171DA1 Series

Reviews:

Related manuals for 0362171DA1 Series

Brands by name

Popular brands