SIEB & MEYER 0362171DA1 Series Hardware Description Download

Page: 5 / 65

About this Manual

This chapter descirbes symbols, signal words and abbreviations used in this manual.

Note

You can download more documentation from the SIEB & MEYER website under

http://

www.sieb-meyer.de/downloads.html

1.1

Illustration of Warnings

In this manual, the warnings listed below are used. Depending on their degree of risk,

the risk levels listed below exist:

DANGER

Imminent risk of injury

Indicates an imminently hazardous situation which, if not avoided, will re-

sult in death or serious injury.
→ Follow the instructions in this manual to avoid danger.

WARNING

Risk of injury

Indicates an imminently hazardous situation which, if not avoided, will re-

sult in death or serious injury.
→ Follow the instructions in this manual to avoid danger.

CAUTION

Slight risk of injury

Indicates a potentially hazardous situation which, if not avoided, may result

in minor or moderate injury or property damage.
→ Follow the instructions in this manual to avoid danger.

NOTICE

Notice

Indicates a hazardous situation which, if not avoided, may result in property damage.
→ Follow the instructions in this manual to avoid danger.

1.2

Abbreviations

FPAM

flux pulse amplitude modulation

HSBLOCK high-speed block commutation

HSPAM

high-speed pulse amplitude modulation

HSPWM

high-speed pulse width modulation

n.c.

not connected

Drive Amplifier SD2B plus - 0362171DA1xxxx, 0362171DB1xxxx

About this Manual

Summary of Contents for 0362171DA1 Series


































































Search results

Summary of Contents for 0362171DA1 Series

Reviews:

Related manuals for 0362171DA1 Series

Brands by name

Popular brands

SIEB & MEYER 0362171DA1 Series, Hardware Description

Search results

Summary of Contents for 0362171DA1 Series

Reviews:

Related manuals for 0362171DA1 Series

Brands by name

Popular brands