SICK UC40 Operating Instructions Manual Download | Manualshive

Page: 32 / 46

background image

7.4.6

Activating and deactivating teach-in buttons and synchronization

Approach

1.

Switch off the supply voltage.

2.

Apply

M

at MF.

3.

Switch on the supply voltage.

4.

Wait for 3 seconds until both

LED 3

and

LED 4

are flashing simultaneously.

✓

LED 1

does not light up.

✓

LED 3

flashes orange 1x: teach-in buttons and synchronization are activated (fac‐

tory setting).

✓

LED 3

flashes orange 2x: teach-in buttons are deactivated, synchronization is acti‐

vated.

✓

LED 3

flashes orange 3x: teach-in buttons and synchronization are deactivated.

✓

LED 3

flashes orange 4x: teach-in buttons are activated, synchronization is deacti‐

vated.

5.

To change the setting, apply

M

at MF for 1 second.

6.

Wait 10 seconds.

✓

The setting is accepted. The device automatically switches to normal operation
mode.

7.4.7

Teaching in several synchronized devices

Important information

NOTE

When teaching-in via pushbuttons or IO-Link, each device continues to be taught-in
individually even in synchronization operation.

Prerequisites

•

Several devices are synchronized with each other (synchronization operation).

•

Teach-in via multifunction input (pin 5) is activated.

Approach

b

Start a teach-in process on one of the synchronized units via the multifunction
input.

✓

This teach-in process is started for all synchronized units.

Example

b

Teach-in a switching point at a device via the multifunction input (Single Point
Mode).

✓

For each synchronized device, its current measured value is taught in as the
switching point.

7.5

IO-Link

Depending on the device type, the device can exchange process data and parameters
via IO-Link. To do this, connect the device to a suitable IO-Link master. A sensor-specific
device description file (IODD) is required in the IO-Link master.

The IODD and additional information are available at

www.sick.com/UC40

7.6

SOPAS ET

The SOPAS Engineering Tool (SOPAS ET) software is suitable for parameterization as
well as for service and diagnostics purposes. SOPAS ET can be used for device types
that come with an IO-Link interface.

7

OPERATION

32

O P E R A T I N G I N S T R U C T I O N S | UC40

8027772//2022-08-11 | SICK

Subject to change without notice

«
...
30
31
32
33
34
...
»

Summary of Contents for UC40















































Reviews:

No comments

Related manuals for UC40

Brand: VDO Pages: 91

Brand: CALEFFI Pages: 20

Brand: Eclipse Pages: 6

Brand: Kathrein Pages: 52

Brand: Manfrotto Pages: 2

Brand: Manfrotto Pages: 2

Brand: Mammut Pages: 32

WorkCentre 7132

Brand: Xerox Pages: 3

Brand: Paradyne Pages: 4

Sleeptrainer Palm the penguin

Brand: NENKO Pages: 4

Brand: Solight Pages: 2

IQ Motion S Series

Brand: QOLSYS Pages: 2

2 SD Card Memory Module NI 9802

Brand: National Instruments Pages: 16

Brand: Blue Ox Pages: 7

Brand: Shad Pages: 3

Brand: Dakota Digital Pages: 6

Brand: DEFA Pages: 7

Brand: Prorack Pages: 15

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands