SICK TMM55 Operating Instructions Manual Download Page 9 | Manualshive

Page: 9 / 36

background image

General parame‐
ters

1

TMS88A-PKC360

TMM88A-PKC090

Dimensions /
Weight

Plastic housing: 66 mm x 90 mm x 36 mm / approx. 200 g

1

All specified angular accuracies apply after a run-in time of 10 min at 25 °C, limit frequency 0.3 Hz,
absolute calibration accuracy (at 25 °C): ±0.05°

Figure 1: TMS88A measuring axis (large plastic housing)

Figure 2: TMS88A measuring axes (large plastic housing)

4.2

Technical data for TMS88A- TMM88A-PLC090

Table 3: Technical data for TMx88A-PLCxxx

General parame‐
ters

1

TMS88A-PLC360

TMM88A-PLC090

Number of measur‐
ing axes

1

2

Measuring range

360°

±90°

Resolution

0.01°

0.01°

Accuracy

Range
0...360°

Typical
±0.04°

Maximum
±0.12°

Range
up to ±60°
up to ±70°
up to ±80°
up to ±85°

Typical
±0.02°
±0.04°
±0.08°
±0.16°

Maximum
±0.06°
±0.12°
±0.24°
±0.48°

Cross sensitivity
(compensated)

-

Typ. ±0.09° (±0.10%FS)
Max. ±0.45° (±0.50%FS)

Temperature coeffi‐
cient (zero point)

Typ. ±0.0083 °/K

Sampling rate

100 Hz

TECHNICAL DATA

4

8019053/1EF6/2021-12-13 | SICK

O P E R A T I N G I N S T R U C T I O N S | TMS/TMM88, TMS/TMM55

9

Subject to change without notice

«
...
7
8
9
10
11
...
»

Summary of Contents for TMM55





































Reviews:

No comments

Related manuals for TMM55

Brand: Gates Pages: 2

AJHVF21G - HD EVF - MULTI-LANG

Brand: Panasonic Pages: 4

Brand: Barnstead Thermolyne Corporation Pages: 16

Brand: Gateway Pages: 4

Brand: Nauticam Pages: 2

Brand: Eachine Pages: 14

Brand: i-SERV Pages: 28

Brand: IDEAL Pages: 6

Brand: IdeaFly Pages: 3

Brand: wattio Pages: 15

Brand: QIMMIQ Pages: 16

Brand: QA1 Pages: 10

Brand: Dometic Pages: 162

GTM 10 - TMC Module

Brand: Garmin Pages: 1

Brand: OBO Bettermann Pages: 2

JX20 - Pura - Headset

Brand: Jabra Pages: 4

Brand: Takex Pages: 11

Brand: GF Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands