manualshive.com logo in svg

SICK SIM2000ST-E, Operating Instructions Manual, Page: 34 / 38

Share
Download
SICK SIM2000ST-E Operating Instructions Manual Download Page 34

Feature

Parameter

Quantity 4

Function Host, AUX, image transmission

Data transmission rate ETH1 – 4: 0.01; 0.1; 1 Gb/s

Protocol TCP/IP, FTP (image transmission)

CAN

Quantity 1

Function SICK CAN sensor network (master/slave, multiplexer/server), ter‐

mination controllable via app

Data transmission rate 20 kbit/s ... 1 Mbit/s

Protocol CSN (SICK CAN sensor network)

IO-Link

Quantity 2 x IO-Link to X2 male connector

Function IO-Link master

Data transmission rate max. 230 kBaud

Protocol V 1.1

Digital switching inputs/outputs

X2 2 configurable inputs/outputs or IO-Link

X2 2 inputs

X3 4 non-insulated outputs (push-pull)

X4 4 isolated inputs

X5 4 isolated inputs

USB

USB 2.0 (mini USB) for configuration/ diagnostics/ firmware
update

11.3

Mechanics and electronics

Feature

Parameter

Operating elements

1 selector switch,
2 S1 and S2 switches for GND ISO/GND

Electrical connection

X1 – POWER: spring terminals
X2 – IO-Link, GPIOs: spring terminals
X3 – OUTPUT: spring terminals
X4 – INPUT A: spring terminals
X5 – INPUT B: spring terminals
X6 – SERIAL A: spring terminals
X7 – SERIAL B: spring terminals
X8 – CAN: spring terminals
X9 ... X14: RJ-45

Supply voltage

24 V DC ± 20% in accordance with EN 61010; also applies to
digital switching inputs

Operating current

limit to max. 6 A from external power supply unit

Power consumption

15 W typ. (at full CPU load, no sensors connected)

Power output

Max. 100 W total (all connections)

Output current

Switching outputs

X2: 100 mA per output
X3: 100 mA per output

11 

TECHNICAL DATA

34

O P E R A T I N G   I N S T R U C T I O N S | SIM2000ST-E

8025454/1BLK/2021-03-30 | SICK

Subject to change without notice

Summary of Contents for SIM2000ST-E







































Reviews:

No comments