background image

© SICK AG • Presence Detection • Subject to change without notice • 8017387 5

Operating instructions IO-Link USB Master SiLink2 Master

General

1  General

1.1 

Information on the Operating Instructions

These operating instructions supplement the supplied Quickstart guide 

and include additional information and more detailed descriptions of 

working with the IO-Link USB Master SiLink2 Master. 
The operating instructions are intended to be used by qualified personnel 

and electrical specialists.

1.2 

Explanation of Symbols

Physical Damage

Warnings in these operating instructions are labeled with symbols. 
The notes must be complied with and careful actions must be taken in 

order to avoid physical damage.

WARNING!

… indicates a possible hazardous situation which may 

lead to physical damage if it is not avoided.

Tips and Recommendations

NOTE!
… highlights useful tips and recommendations as well as 

information for efficient and hassle-free operation.

1.3 

Scope of Delivery

Included with delivery:
•  SiLink2 Master IOLA2US
•  1 USB cable
•  1 wall plug
Supplied documentation:
•  Quickstart

Summary of Contents for SiLink2 Master IOLA2US-01101





















Reviews: