SICK midiCam2 Operating Instructions Manual Download Page 12 | Manualshive

Page: 12 / 24

background image

5

Mounting

5.1

Mounting instructions

•

Observe the technical data.

•

Protect the sensor from direct sunlight.

•

To prevent condensation, avoid exposing the device to rapid changes in tempera‐
ture.

•

The mounting site has to be designed for the weight of the device.

•

Protect the device from moisture, contamination, and damage.

•

Ensure a sufficient level of cooling using ambient air/convection and/or heat dissi‐
pation through mechanical mounting. Observe the permitted operating tempera‐
ture,

see "Technical data", page 19

.

5.2

Mounting the device

1.

Mount the device using the designated fixing holes,

see "Dimensional drawing",

.

2.

Make the electrical connection. Attach and tighten a voltage-free cable,

necting the device electrically", page 14

3.

Switch on the supply voltage.

✓

The LED flashes green.

4.

Align the device so that the desired object is recorded.

5

MOUNTING

12

O P E R A T I N G I N S T R U C T I O N S | midiCam2

8025780/0000/2020-07 | SICK

Subject to change without notice

«
...
10
11
12
13
14
...
»

Summary of Contents for midiCam2

























Reviews:

No comments

Related manuals for midiCam2

FE 220 - Digital Camera - Compact

Brand: Olympus Pages: 77

FE 200 - Digital Camera - 6.0 Megapixel

Brand: Olympus Pages: 72

FE 190 - 6MP Digital Camera

Brand: Olympus Pages: 80

FE 190 - 6MP Digital Camera

Brand: Olympus Pages: 80

FE 170 - Digital Camera - 6.0 Megapixel

Brand: Olympus Pages: 77

FE 130 - 5.1MP Digital Camera

Brand: Olympus Pages: 80

Brand: Olympus Pages: 2

Brand: Olympus Pages: 2

Brand: Olympus Pages: 196

E-500 - EVOLT Digital Camera

Brand: Olympus Pages: 128

E-500 - EVOLT Digital Camera

Brand: Olympus Pages: 216

Brand: Olympus Pages: 172

Brand: Olympus Pages: 172

E-410 - EVOLT Digital Camera SLR

Brand: Olympus Pages: 2

Brand: Olympus Pages: 6

Brand: Olympus Pages: 7

CAMEDIA C-500 Zoom

Brand: Olympus Pages: 100

Brand: Olympus Pages: 84

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands