manualshive.com logo in svg

SICK Lector62 Series, Online Help Manual, Page: 57 / 131

Share
Download
SICK Lector62 Series Online Help Manual Download Page 57

151

Separator Character Replacement

In the GS1 code format, the 

Separator Character Replacement

 parameter can be used

to define user-specific characters for the separator (control character within the code).

The characters are entered via the keyboard or clipboard.

It is possible to select special characters or enter hexadecimal characters via the 
symbol.

Information on editing the characters is available via the 

 symbol.

152

Expected Number of Characters 1

This parameter can be used to determine the number of expected characters in a line.

The number of expected characters must be specified. The algorithm uses this value to
optimize the search for characters.

153

Number of Lines Expected

The 

Number of Lines Expected

 parameter determines the number of lines in the image

expected by the sensor.

The number of expected lines must be specified. The algorithm uses this value to opti‐
mize the search for lines of text.

154

EtherNet/IP

Device communication via Ethernet/IP can be activated and configured on the 

Ether‐

Net/IP

 tab.

155

EtherNet/IP enabled

Device communication via Ethernet/IP is activated/deactivated via the 

EtherNet/IP

enabled

 parameter. Once Ethernet/IP has been activated, the reading device must be

restarted.

156

Ethernet

The 

Ethernet

 tab contains all of the parameters for configuring the Ethernet interface.

The device address and the configuration data for the host and aux ports can be
entered on the tab.

157

Ethernet General

The 

Ethernet General

 group contains general parameters for configuring the Ethernet

interfaces (host and aux).

158

Ethernet Aux

If the 

Ethernet Aux

 parameter is activated, the results from the Ethernet aux interface

are written to the save destination.

SOPAS PARAMETER OVERVIEW

8013778/YPV6/2016-01-14 | SICK

O N L I N E   H E L P | Lector62x

57

Subject to change without notice

Summary of Contents for Lector62 Series




































































































































Reviews:

No comments