SICK Lector62 Series Online Help Manual Download Page 56 | Manualshive

Page: 56 / 131

SICK Lector62 Series Online Help Manual Download Page 56

147

Allowed Characters / Scoring

A character filter can be used to limit the number of characters to be read and a scor‐
ing system activated in the

Allowed Characters / Scoring

group.

Setting the character filter limits the number of characters to be detected for the
selected character position. When the filter is set, the stability and accuracy of the
reading is increased and the reading time is reduced. Depending on the font used, the
character “1” is similar to the characters “I” and “J”. “F” is similar to “P” and “C” is simi‐
lar to “G”.

The scoring system specifies how identical the detected character is to the taught-in - or
ideal - character. The maximum value is 100.

148

Allowed Character 1

This parameter is used to define allowed characters for a character position by setting a
character filter in the field at the desired position.

Character filter:

•

? – ALL CHARACTERS

: All characters are expected and detected by the sensor at this

position.

•

$ – ONLY A-Z

: Only upper-case letters of the Latin alphabet are expected and

detected by the sensor at this position.

•

* – ONLY A-Z

: Only lower-case letters of the Latin alphabet are expected and detected

by the sensor at this position.

•

# – ONLY NUMBERS

: Only numbers are expected and detected by the sensor at this

position.

•

% – ONLY SPECIAL CHARACTERS

: Only special characters are expected and detected by

the sensor at this position.

•

& – ONLY A-Z + NUMBERS

: Only upper-case letters of the Latin alphabet and numbers

are expected and detected by the sensor at this position.

•

A - CHARACTER TO BE READ (E.G., A)

: The sensor only expects and detects the character

specified in the field at this position.

NOTE

If a filter is only set for numbers, for example, letters will not be accepted when teach‐
ing in is subsequently carried out.

149

Calculated Speed

The current speed is indicated in the

Calculated Speed

display field.

For this to happen, a connection must be established between the sensor and the PC.

150

FNC1 Character Replacement

In the GS1 code format, the

FNC1 Character Replacement

parameter can be used to

define user-specific characters for the FNC1 character (control character at the start of
the code).

The characters are entered via the keyboard or clipboard.

It is possible to select special characters or enter hexadecimal characters via the
symbol.

Information on editing the characters is available via the

symbol.

SOPAS PARAMETER OVERVIEW

56

O N L I N E H E L P | Lector62x

8013778/YPV6/2016-01-14 | SICK

Subject to change without notice

«
...
54
55
56
57
58
...
»

Summary of Contents for Lector62 Series




































































































































Reviews:

No comments