manualshive.com logo in svg

SICK Lector62 Series, Online Help Manual, Page: 120 / 131

Share
Download
SICK Lector62 Series Online Help Manual Download Page 120

362

Teach-in stop by

Depending on how the 

Start teach-in

 parameter has been configured, the 

Teach-in stop

by

 parameter is used to define which signal or condition should terminate the teach-in

process for the match code.

•

TEACH-IN TRIGGER SOURCE

: The teach-in process is terminated by a signal (e.g., a key

switch) at one of the sensor's digital inputs.

•

OBJECT TRIGGER

: The teach-in process is terminated as soon as the reading gate

closes.

•

VALID CODE TAUGHT IN

: The teach-in process is terminated as soon as a match code

has been successfully read.

363

Teach-in Condition

The 

Teach-in Condition

 parameter defines the condition that must apply when the newly

taught-in match code content is stored. The selected condition is used as a basis when
the target/actual comparison is activated. Each code that is read is compared to the
code content that was read in for the target condition.

The 

Teach-in Condition

 parameter is used to assign the items of code content that are

to be compared to a condition. The taught-in match codes can be retrieved and acti‐
vated at a later time, subject to the condition being met.

364

EDS Text Element in Output Format / Assign Element EDS of Output Format

You can use this option if you want data from an external device such as a 

weighing

scale

 to be 

combined

 with the sensor data. This allows the reading result and the exter‐

nal data to be sent to the host 

in one string

.

For this to take place, the external data must be received by the sensor 

while the read‐

ing gate is open

. If the sensor does not receive any data during the reading gate inter‐

val, a default text is sent so that the host is aware that no data has been received. It
makes the most sense to use this option when data is output at the end of the cycle.

The EDS text element can be positioned freely as a variable in the output format and
can be set to a fixed length by double-clicking.

Data is output on 

all configured interfaces

, including the fieldbus interfaces.

365

Timeout

If the 

Data transmission point

 parameter is set to the 

END OF LABEL

 value, the 

Timeout

parameter can be used to define how much time must elapse before a code is output
again.

The unit can be selected via the 

Output delay

 parameter.

366

Timeout Diag. Output

The 

Timeout Diag. Output

 parameter defines an interval in ms during which reading

diagnosis data remains available in the object directory for upload by the control. Once
this interval has elapsed, the reading diagnostic data is discarded.

Alternatively, the timeout values can be modified directly in the object directory via
objects 0x3010/01 to 0x3010/02. The changes are not applied until the device has
been restarted.

If the reading diagnostic data is being monitored, the data is stored in the object direc‐
tory and downloaded by the control. A timeout must be specified for the upload.

SOPAS PARAMETER OVERVIEW

120

O N L I N E   H E L P | Lector62x

8013778/YPV6/2016-01-14 | SICK

Subject to change without notice

Summary of Contents for Lector62 Series




































































































































Reviews:

No comments