Home
/
SICK
/
Lector62 Series
/
Online Help Manual

SICK Lector62 Series, Online Help Manual, Page: 114 / 131

Share

Page: 114 / 131

SICK Lector62 Series Online Help Manual Download Page 114

344

Start teach-in

parameter is used to select the signal that triggers the automatic

process for teaching in a match code.

•

AUTOMATIC / STATIC

: A signal (e.g., a key switch) makes the reading gate open auto‐

matically. The next code read by the system is taught in as a match code.

•

SYSTEM TRIGGER / DYNAMIC

: A signal (e.g., a key switch) at one of the sensor's digital

inputs prepares it for teaching in a match code. Once the reading gate has opened
(typically triggered by a photoelectric switch), the next code read by the system is
taught in as a match code.

345

Start delay

parameter can be used to control when the reading window opens. The

unit can be selected via the

parameter.

If a positive value is set, the reading gate opens at a later point, e.g., so that the sensor
only detects codes at the rear end of an object in order to reduce the decoding time.

Image capture can be tailored more precisely to the code position by adjusting the trig‐
ger.

•

A START DELAY

(additional time/distance for which the reading gate must remain

closed after event A)

346

Station Name

A name for the PROFINET IO gateway is defined via the

parameter.

The following naming conventions apply:

•

The station name consists of letters, digits, a dash, or a period, and must not
exceed 127 characters.

•

A single component of the device name, i.e., a string of characters between two
periods, must not exceed 63 characters.

•

With the exception of hyphens, special characters must not be used.

•

The device name must not start or end with a hyphen or period.

•

The device name must not begin with digits.

•

The device name must not be in the form of n.n.n.n (where n is a number between
0 and 999).

•

The device name must not start with the character sequence "port-xyz-" (where
x,y,z are numbers between 0 and 9).

347

Increase of decoding robustness

The settings in the

Increase of decoding robustness

group are used to increase the

readability of codes when the print quality is poor. However, these settings reduce the
reading reliability.

SOPAS PARAMETER OVERVIEW

114

O N L I N E H E L P | Lector62x

8013778/YPV6/2016-01-14 | SICK

Subject to change without notice

«
...
112
113
114
115
116
...
»

Summary of Contents for Lector62 Series




































































































































Reviews:

No comments