manualshive.com logo in svg

SICK Lector62 Series, Online Help Manual, Page: 106 / 131

Share
Download
SICK Lector62 Series Online Help Manual Download Page 106

316

Text Color

The 

Text Color

 parameter is used to define the difference in color between the text and

background.

•

BLACK

: Text is darker than the background

•

WHITE

: Text is lighter than the background

•

AUTOMATIC

: Automatic detection

NOTE

To increase the stability of reading it is recommended that the text color is defined.

317

Display Score Values in the Image

If the 

Display Score Values in the Image

 parameter is activated, the determined score

values are shown in the image.

318

Check SD card

You can check whether the memory card is in working order by pressing the 

Check SD

card

 button.

319

Sensor / Input 1

The 

Sensor / Input 1

 group contains parameters for adjusting digital input 1.

The 

Control system

 parameter allows you to choose between a configuration based on

length units and a configuration based on time units.

•

DISTANCE-CONTROLLED

: The configuration is based on distance increments in mm.

These are either generated by the configuration software (SOPAS)/CAN interface
or via a rotary encoder at the digital input.

•

TIME-CONTROLLED

: The configuration is based on times entered in ms.

The 

Empfindlichkeit

 parameter allows you to choose between edge control and level

control.

•

EDGE

: The digital input responds to the switch between Low (0) and High (1)

according to how the 

Logic

 parameter is configured. Any signal that is permanently

present is ignored.

•

LEVEL

: The digital input responds to a permanently present signal according to how

the 

Logic

 parameter is configured.

The 

Logic

 parameter is used to select the polarity for the 

Sensitivity

 parameter.

•

NOT INVERTED

: The digital input responds to a rising edge, i.e., to a switch from Low

(0) to High (1), or to a High signal (1) that is permanently present.

•

INVERTED

: The digital input responds to a falling signal edge, i.e., to a switch from

High (1) to Low (0), or to a Low signal (0) that is permanently present.

Depending on how the 

Control system

 parameter is configured, the 

Debouncing

 param‐

eter specifies the minimum distance in mm or the minimum time in ms for the signal at
the external input. If the value is not achieved, the signal is not detected.

Depending on the application, this value may have to be adapted in line with the read
cycle rates required.

320

Sensor / Input 2

The 

Sensor / Input 2

 group contains the parameters for adjusting digital input 2.

SOPAS PARAMETER OVERVIEW

106

O N L I N E   H E L P | Lector62x

8013778/YPV6/2016-01-14 | SICK

Subject to change without notice

Summary of Contents for Lector62 Series




































































































































Reviews:

No comments