SICK IOLG2PN-03208R01-PROFINET Operating Instructions Manual Download Page 6 | Manualshive

Page: 6 / 50

SICK IOLG2PN-03208R01-PROFINET Operating Instructions Manual Download Page 6

Operating instructions IO-Link Master IOLG2PN-03208R01 – PROFINET

General information

6

© SICK AG • Presence Detection • Subject to change without notice • 8018665.10RD

1.4

Limitation of liability

Applicable standards and regulations, the latest state of technological

development, and many years of knowledge and experience have all been

taken into account when assembling the data and information contained in

these operating instructions.
The manufacturer accepts no liability for damage caused by:
•  Failing to observe the operating instructions
•  Incorrect use
•  Use by untrained personnel
•  Opening the housing
•  Unauthorized conversions
•  Technical modifications
•  Use of defective devices
•  Use of unauthorized spare parts/consumable parts.
With special variants, where optional extras have been ordered, or owing to

the latest technical changes, the actual scope of delivery may vary from the

features and illustrations shown here.

1.5

Scope of delivery

Included with delivery:
•  IO-Link Master PROFINET IOLG2PN-03208R01
•  4 M12 blind plugs for sealing unused IO-Link ports
•  M4 ground strap with M4 x 6 screw
•  20 labels

Supplied documentation:
• Quickstart

1.6

Customer service

If you require any technical information, our customer service department

will be happy to help.
See the back page for your representative office.

NOTE!
In order to allow us to deal with the matter quickly, please

note down the type designation and order number before

calling. This information can be found on the side of the

IO-Link Master.

«
...
4
5
6
7
8
...
»

Summary of Contents for IOLG2PN-03208R01-PROFINET



















































Reviews:

No comments