SICK IOLG2PN-03208R01-PROFINET Operating Instructions Manual Download

Page: 30 / 50

Operating instructions IO-Link Master IOLG2PN-03208R01 – PROFINET

System integration and configuration

Parameter server

The following options are available for the parameter server:

Option

Description

Switched on

Data storage function is active. Parameter and identifica-

tion data for the IO-Link device is saved retentively.

Switched off

Data storage function is deactivated. The saved data are

retained.

Deleted

Data storage function is deactivated. The saved data is

deleted.

Enable of block

upload

Enable or block the parameter data upload into the IO-Link

Master port data storage.
• Enable upload: The IO-Link Master starts to upload the

parameter data as soon as an IO-Link device requests

an upload (upload flag set) or if there is no data stored

in the master port, e.g., after the data has been deleted

or before the first data upload

• Block upload: If the upload is blocked, the data is not

uploaded. If an IO-Link device sends an upload request,

a download starts if there are different parameter sets

since an upload cannot take place. The download must

be enabled.

Enable or block

download

Enable or block the parameter data download to the IO-

Link device.
• Enable download: As soon as the saved parameter

data in the parameter server of the port differs from a

connected IO-Link device and there is no upload request

from the IO-Link device, a download is performed.

• Block download: If the download is blocked, the parame-

ter data is uploaded if it is activated. The upload flag for

the IO-Link device does not need to be set in this case.

The upload must be enabled.

Block upload and

download

If both upload and download are blocked, the parameter

data is not exchanged. However, the IO-Link device still

communicates with the IO-Link port.

Table 15: Parameter server

NOTE!
After the parameter data upload, the vendor ID and de-

vice ID are retained until the data sets of the connected

IO-Link device are deleted.
A validation takes place when the connected IO-Link de-

vice starts up. This means that only one IO-Link device of

the same type can be used for data storage. In order to

use an IO-Link device of a different type, you must delete

the content of the parameter server.

Summary of Contents for IOLG2PN-03208R01-PROFINET



















































Search results

Summary of Contents for IOLG2PN-03208R01-PROFINET

Reviews:

Related manuals for IOLG2PN-03208R01-PROFINET

Brands by name

Popular brands

SICK IOLG2PN-03208R01-PROFINET, Operating Instructions Manual

Search results

Summary of Contents for IOLG2PN-03208R01-PROFINET

Reviews:

Related manuals for IOLG2PN-03208R01-PROFINET

Brands by name

Popular brands