manualshive.com logo in svg

SICK FX3-MOC1, Operating Instructions Manual

Share
Download
SICK FX3-MOC1 Operating Instructions Manual Download Page 33

The additional information provided in this chapter just offers an overview of the soft‐
ware.

7.3.1

Pre-configured project files

Pre-configured project files for the safety system are available under the following link:

www.sick.com/Safe_Linear_Positioning

Separate project files are available for both variants of the sensor and they have differ‐
ent sensor settings. In these project files, all configurable parameters are set to stan‐
dard values.

Aside from the project files provided, export files are available on the internet. These
correspond to the hardware configuration and logic of the project files, but can be
imported into any Flexi Soft CPU module (from firmware version 4.xx). The checksums
listed below result. After downloading or importing, it must be checked whether the
checksum of the project corresponds to the respective checksum indicated here. The
checksums change if modifications are made to the parameters or logic.

7.3.1.1

Project and export file for SSI protocol 24+1 bit (SAPPD3E-14AP003)

FX3-CPU0 with Flexi Soft project file ID no. 9288608

Table 15: Checksum with possible pin assignment on FX3-MOC1 module

MOC input E1

Not assigned

MOC input E2

BG100.2 OLM sensor 2 as SSI master 24+1 bit

Checksum

0xA126F159

Table 16: Checksum with possible pin assignment on FX3-MOC1 module

MOC input E1

BG100.1 OLM sensor 1 as SSI listener 24+1 bit

MOC input E2

BG100.2 OLM sensor 2 as SSI master 24+1 bit

Checksum

0xD904FC86

Table 17: Checksum with possible pin assignment on FX3-MOC1 module

MOC input E1

BG100.1 OLM sensor 1 as SSI master 24+1 bit

MOC input E2

BG100.2 OLM sensor 2 as SSI master 24+1 bit

Checksum

0x771CA6AB

FX3-CPU1 with Flexi Soft export file “SSI master” ID no. 9288609

Table 18: Checksum with possible pin assignment on FX3-MOC1 module

MOC input E1

BG100.1 OLM sensor 1 as SSI master 24+1 bit

MOC input E2

BG100.2 OLM sensor 2 as SSI master 24+1 bit

Checksum

0x05D4F6D0

FX3-CPU1 with Flexi Soft export file “SSI listener” ID no. 9290537

Table 19: Checksum with possible pin assignment on FX3-MOC1 module

MOC input E1

BG100.1 OLM sensor 1 as SSI listener 24+1 bit

MOC input E2

BG100.2 OLM sensor 2 as SSI master 24+1 bit

Checksum

0xABCCACFD

CONFIGURATION 

7

8020941/12O9/2019-08-05 | SICK

O P E R A T I N G   I N S T R U C T I O N S | Safe Linear Positioning

33

Subject to change without notice

Summary of Contents for FX3-MOC1

































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands