background image

Installation FLSE100-XT                                                                                 

FLOWSIC100 Flare-XT · Operating Instructions · 8023761/V1-0/2020-10 · © SICK Engineering GmbH

65

5.6.8.1

Calculating the wetted part length wL and geometric installation parameters

Before installation, calculate how deep the sender/receiver units will be pushed into the

pipeline.
The wetted part length depends on:
● Nozzle length
● Gasket thickness
● Ball valve length
● Wall thickness

Calculating the wetted part length with the geometry calculator 

1

Open the geometry calculator.

2

First select in the “Path number” field of the “Calc length, angle, diameter” tab whether 

it is a 1-path or 2-path installation. 

3

In the field “Sensor type” (Transducer type), select whether the device is a “Cross duct” 

or “Probe” version.

4

Select “retractable” for installations with ball valve and “non retractable” for installa

-

tions without ball valve.

5

For cross-duct versions, enter the probe distance “Transducer distance” a determined 

for the nozzle installation tool,  



p. 54, §5.6.7.2

.

6

Enter the required dimensions:
– Circumference U
– Wall thickness w
– Gasket thickness S
– Gasket thicknesses D1 and D2
– For installation with ball valve: Length of ball valve VL
– Angle β: For cross-duct versions, enter the nominal nozzle angle (e.g. 75°, 60°, 

45°). For the probe version, measure the installation angle and enter the exact 

value (maximum value for measuring the installation angle: ±0,3 °).

The wL (“wetted part length”) and geometric installation parameters are calculated.

NOTICE:

The wall thickness must be determined accurately to 0.1 mm. SICK 

recommends using a suitable ultrasonic measuring instrument to determine 

the wall thickness.

NOTICE:

The geometric installation parameters in the “Result: Parameters for configu

-

ration” area and the wall thickness are required for configuring the measuring 

system during commissioning.

Summary of Contents for FLOWSIC100 Flare-XT





























































































































































































Reviews: