manualshive.com logo in svg

SICK Flexi Classic, Operating Instructions Manual

Share
Download
SICK Flexi Classic Operating Instructions Manual Download Page 100

Chapter 

9

Operating Instructions 

Flexi Classic Gateways

 

100

 

© SICK AG • Industrial Safety Systems • Germany • All rights reserved 

8011834/YT28/2016-03-15 

Subject to change without notice 

EtherNet/IP Gateway 

Read-from-Tag/file — UE410-EN requests the data from the PLC. 

In this operating mode the UE410-EN as master requests the data continuously from the 
PLC in order to set the digital outputs. If this operating mode is desired: 

Select the operating mode 

Read-from-Tag/File

 in the 

Tx (from PLC) Transfer Mode

 

selection field. 
Carry out the following settings on the same web page (see Tab. 91): 
– PLC IP Address 
– PLC Controller Slot Number 
– Digital Output Polling Enable 
– Digital Output Tag/File Name 
– Digital Output Setting Poll Rate 
Activate 

Save in Flash

 and click 

Submit

 to save the selection. 

Only if 

Save in Flash

 is checked, the new configuration will be stored in the UE410-EN’s 

non-volatile memory and be available after a restart of the gateway. 

Submit

 without 

checking 

Save in Flash

 allows, for example, the testing of new configurations without 

overwriting the old configuration. 

9.5

 

Configuration of the gateway — which data are 

transferred 

The UE410-EN processes the data of a Flexi Classic system and makes them available in 
different compilations, the data sets for the PLC.  
There are 6 data sets available to this purpose: Data sets 1-5 contain fixed data compila-
tions, Data set 6 can be configured by the user. The data sets that are to be transferred to 
the PLC must be activated (see section 7.8). 

Open a web browser on a PC in the network and go to the address of the UE410-EN. 
Click 

Flexi System Interface Configuration

 on the UE410-EN homepage. 

The following web page is displayed: 

The installed Flexi Classic modules are recognised automatically and listed in the 

Flexi 

Chassis Configuration

 field. Modules of the next Flexi Classic generation that are not yet 

recognised by the UE410-EN1 are listed as “Unknown Module”. The corresponding front 
and the data structure of the module can be displayed by clicking a module. In the exam-
ple, a click on 

Module 1

 displays a new window with the corresponding information. The 

window can subsequently be closed again. 

Note 

Summary of Contents for Flexi Classic





























































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands