background image

ANNEX   

 

167 

8020776/12AX / 2019-05-31|SICK 

Subject to change without notice 

O P E R A T I N G   I N S T R U C T I O N S |Free Flow Profiler 

 

9.3.2

 

North American region 

North America uses a detailed categorization system, the 

North America Detailed

, with 

30 categories. These categories are grouped into 11 broader categories under the 

North 

America Consolidated

 category system. 

In vehicle information, these categories are described as follows:  

… 
<Category> 

<Value>

NorthAmericaDetailed

.AutomobileWithTrailer</Value> 

</Category> 

<CategoryExternal> 

<Value>

NorthAmericaConsolidated

.AutomobileWithTrailer</Value> 

</Category> 

… 

 

Category Systems  

 

 

North America Detailed 

(Class No. and Name) 

North America  

Consolidated 

(Class No. and Name) 

Description 

Symbol 

Unknown 

Unknown 

Detectable, but not classifiable vehicle 

 

110 

Motorcycle 

Motorcycle 

Motorbike or scooter (without bicycle or 

moped) 

 

111 

MotorcycleWithTrailer 

MotorcycleWith

Trailer 

Motorbike or scooter with trailer of all types 

 

210 

Automobile 

Automobile 

Automobiles of all types, with load on the roof, 

with bicycle attached at the back 

 

211 

AutomobileWithTrailer  4 

AutomobileWith

Trailer 

Automobiles with trailer of all types, empty / 

nearly empty / loaded 

 

320 

Pick-up 

VanPickup 

Pick-ups of all types, with / without load at the 

back, on the top 

 

310 

Van 

Van with tapered front, including school van 

and pickup with hard top 

 

350 

VanCommercial 

Vans with tapered front and high cubical back 

 

1302 

PickupSnowPlow 

Pick-ups with a snow-plow mounted in the front 

 

321 

PickupWithTrailer 

VanPickupWith 

Trailer 

Pick-ups with trailer of all types, empty /  

nearly empty / loaded 

 

311 

VanWithTrailer 

Vans with trailer of all types, empty /  

nearly empty / loaded 

 

351 

VanCommercialWith 

Trailer 

 

 

Vans with tapered front and high cubical back, 

with trailer of all types, empty / nearly empty / 

loaded 

 

340 

PickupKingpin 

Pick-ups with kingpin, regardless of loading 

 

Summary of Contents for 1088784





















































































































































































Reviews: