Package
Overview
Installation
1
2
3
4
2
1
3
*
1 It
is
recommended
to
install
the
water
-
proof
cap
for
network
cable connection
.
*
2
If
the
PoE network switch is
used
to
connect
the
camera, DC12V
power supply
is
not
required
.
Thank you for purchasing Sibell. We are always looking to
improve and will update the products or procedures as technology
changes and the industry adapts. If you need further product
assistance please contact your technical support specialist.
Content is subject to change without notice.*
Warning
and
Caution
■ If the product does not work properly, please contact your dealer or the
nearest service center. Never attempt to disassemble the camera yourself.
(We shall not be responsible for any problems caused by unauthorized
repair or maintenance.)
■ Keep away from liquid while in use due to risks of electric shock.
■ When using this product, you must be strict compliance with electrical
safety regulations to reduce the risk of electric shock. When the product
is mounted on the wall or ceiling, the device should be secured firmly.
■ Do not use camera beyond specified voltage range.
■ Do not drop the camera or damage the camera physically.
■ Avoid touching the camera lens.
■ If cleaning is necessary, please use clean cloth to wipe the lens gently.
If the device will not be in use for a long period of time, please cover the
lens with lens cap to protect the device.
■ Do not aim the camera at the sun or extra bright illumination.
■ Do not place the camera in dusty, damp or extremely hot, or cold
situations/locations (the operating temperature is
(
-4˚F~122˚F/-20˚C~50˚C
), and do not expose it to high
electromagnetism or radiation.
■ To avoid heat accumulation, good ventilation is required for operating
environment.
■ Regular Maintenance is recommended for all users.
Quick
Start
Guide
Network
Camera
Please make sure that the wall or ceiling is strong enough to withstand 3
times the weight of the camera. Please install and use
the camera in
a
dry
environment.
Advised: If lens cover is removed, re apply cover within 4 hours
②
Route the cables and connect the relevant cables.
③
Mount the rubber plug to the gap of the mounting base. Then
secure the mounting base with camera to the wall with screws.
Camera
Quick
start
guide
CD
Water
-
proof
cap
Plastic
plug
×4
Drill
template
Rubber
plug
CVBS&DC
IN cables
Screwdriver
4 tapping screws PA4×25
1 machine screw PWM3×5
∅
22.6
∅
91.4
∅
103
∅
5
64.6mm
64.6mm
90°
Microphone Cable
Headphone Cable
TF
Card
Slot
Network Indicator
Reset
Hole
CVBS/DC IN port for testing
Alarm Input/Output
RS485 Cable
Network Cable
Power
Cable
Zoom
Focus
1
2
3
5
7
9
4
6
8
10
11
12
ALM-COM
ALM-NO
ALM-IN
ALM-GND
RS485T-
N
et
w
or
k C
ab
le
●
Alarm Input
: Join the grounding ends of the sensor and the camera
and then connect the signal cable of the sensor to the alarm input
port of the camera.
Alarm Output
: Loosen the screws in the alarm output port. Then
insert the signal wires of the alarm output devices into the port of
NO and COM separately. Finally tighten the screws. Some of the
external alarm output devices need the power supply.
●
Connecting
Network
Cable
Alarm Connection
8
9
10
11
12
2
3
4
5
6
1
7
①
Loosen
the
nut
from
the
main
element.
②
Run
the
network
cable (without
RJ 45
connector) through the
both elements. Then
crimp
the
cable
with
RJ 45
connector
.
③
Connect
the
cable
to
the
hermetic
connector
.
Then
tighten
the
nut
and
the
main
cover
.
To Use Water-proof Cap:
you must have experience in cable termination
①
Drill the screw holes and the cable hole on the wall according to
the drill template.