background image

Shure Incorporated

8/14

Color

State

Error LED amber flashing

Charging stopped. To resume charging, try these solutions:

1. Check that the battery contacts are clean and undamaged. If 

contacts are dirty or damaged, the charger might not detect the 

batteries.

2. Check the temperature. If the battery temperature is above 60°C 

or below 0°C, the error LED flashes.

3.

Contact Shure service. Battery may be discharged beyond re­

covery or have internal problems. Replace battery.

• Error LED amber steady on 4 charg­

ers

Error LED amber flashing on all 

chargers

Too many chargers (more than 4) are connected to each other. Re­

move additional chargers.

Charge status LED red

Error LED amber flashing

Battery too warm. Charging stops at 80% of full capacity. Allow bat­

tery to cool below 45°C to resume charging to full capacity.

Charge status LED green

Error LED amber flashing

Charging complete, but battery temperature is too warm or cold 

(over 60°C or below 0°C).

Power LED red

Charger is in storage mode. Batteries are charging or discharging 

to storage voltage.

Power LED red

Charge status LED amber

Batteries are ready for storage.

Power LED red

Charge status LED red flashing

Batteries are approaching storage voltage.

Power LED white flashing

Charger firmware is being updated.

All LEDs flashing

Hardware identification.

Tip: 

Wireless Workbench provides more detailed battery status information, including temperature and overall 

health.

Storage Mode

To store batteries for longer than 8 days, use the charger's storage mode. Each battery will be charged or dis­

charged to 3.8 volts, which is ideal for long-term storage.

Summary of Contents for SBC220















Reviews: