Model S39A Vibration/Isolation Stand
and S37A Desk Stand User Guide
©
2004, Shure Incorporated
27B848 (Rev. 4)
Printed in U.S.A.
MODEL S39A VIBRATION ISOLATION STAND WITH
SWIVEL ADAPTER
The Model S39A Vibration Isolation Stand provides excellent
shock isolation, preventing floor or table vibrations from reaching a
mounted microphone. Use the S39A for sportscasting, conference
table or front-of-stage installations, or any application where
severe vibrations may occur.
INSTALLING MICROPHONES ON S39A
1. Mount lightweight microphones directly to the S39A.
2. Mount heavier microphones with bottom-entry cable connec-
tors on the provided extension adaptor. The extension adapter
increases the amount of cable-connector clearance.
3. Fasten swivel adapters or extension adapters to the S39A with
the supplied brass attachment screw.
4. Insert the screw through the bottom of the stand base and
tighten with a large screwdriver.
5. To make adjustments, loosen the screw, adjust, then tighten
the screw.
NOTE
: Do not use the S39A with microphones weighing
over 1 kilogram (2.25 lbs.). Excessive weight reduces the
effectiveness of the isolation.
SPECIFICATIONS:
Weight:
964 g (2.125 lbs.)
Dimensions
: See Figure 1
MODEL S37A DESK STAND
The Model S37A Desk Stand provides a low profile, stable base for
microphones with swivel connector assemblies, or microphones
using swivel adapters.
INSTALLING SWIVEL CONNECTOR ASSEMBLIES ON S37A
(FIGURE 2):
1. Place the microphone in the recess at the top of the base.
2. Fasten the microphone to the base with the provided brass
attachment screw.
3. Insert screw through the bottom of the base and tighten with a
large screwdriver.
4. Insert the cable-connector plug into the microphone receptacle.
5. Place the cable in the groove in the bottom rear of the base.
6. Clamp the cable to the base using the provided clamping strip
and machine screws.
NOTE
: The supplied mounting plate is not used with
swivel connector assemblies.
USE WITH SWIVEL ADAPTERS (FIGURE 3):
1. Place the provided mounting plate in the recess at the top of
the base.
2. Position the swivel adapter on top of the mounting plate so
that the swivel adapter projection fits into the notch on the
mounting plate. Secure it with the supplied brass screw.
3. Tighten the brass attachment screw with a large screwdriver.
SPECIFICATIONS:
Finish:
Non-reflective gray
Weight:
691g (1.5 lbs)
Dimensions:
See Figure 4
SHURE Incorporated Web Address: http://www.shure.com
5800 W. Touhy Avenue, Niles, IL 60714-4608, U.S.A.
In U.S.A., Phone: 1-847-600-2000 Fax: 1-847-600-1212
In Europe, Phone: 49-7131-72140 Fax: 49-7131-721414
In Asia, Phone: 1-852-2893-4290 Fax: 1-852-2893-4055
International Fax: 1-847-600-6446
88.9 mm
3-1/2 IN
54 mm
2-1/8 IN
66.7 mm
2–5/8 IN
130 mm
5-1/8 IN
183 mm
7-3/16 IN
65.1 mm
2-9/16 IN
116 mm
4-9/16 IN
73 mm
2-7/8 IN
165 mm
6-1/2 IN
FIGURE
FIGURE 4
FIGURE 1
SWIVEL
ADAPTER
MOUNTING
PLATE
SCREW
SCREW
SWIVEL
CONNECTION
CABLE
CONNECTION
FIGURE 2
FIGURE 3
