![background image](http://html1.mh-extra.com/html/shure/microflex-mxw/microflex-mxw_quick-start-manual_1262375009.webp)
9
Linking Microphones
Use the Networked Charging Station (NCS) to Link microphones to Access Point channels. Slots in the charger are mapped to the APT according to the
Group setup from the Configuration tab. Once the Link procedure is complete, audio will route to the corresponding channel in the Group.
Linking will map any microphone placed in the charging station to the APT channels. This replaces any prior microphone Link for that channel. If a slot is
empty during the Link procedure, there will be no impact on that channel.
1. Arrange microphones in the charger.
Microphones are Linked to access point channels according to the
arrangement in the charger.
For gooseneck mics
7
8
6
5
1
2
3
4
Link
Power
7
6
5
1
2
3
For bodypacks, handhelds and
boundary mics.
7
8
6
5
1
2
3
4
Link
Power
7
8
6
5
1
2
3
4
link
6
5
1
2
link
+
7
8
6
5
1
2
3
4
lockout
power
ethernet
network audio
push to solo | hold to mute
-9
-18
-24
-36
-48
-60
0
-9
-12
-18
-24
0
aux
mic
adjust
line
sig/clip
mute
INPUT
A
sig/clip
mute
OUTPUT
HEADPHONE
Audio Network Interface
MICROFLEX WIRELESS
B
1
2
3
4
5
6
7
8
line
aux
push to solo | hold to mute
sig/clip
mute
INPUT
A
sig/clip
mute
OUTPUT
B
1
2
3
4
5
6
7
8
line
aux
6
7
8
9
10
11 12 1
2
3
4
5
6
7
8
9
10
11 12 1
2
3
4
5
5
7
8
6
5
1
2
3
4
i i i i i i i i i i
i i
i i i
i i i i i i i i i i
i i
i i i
i i i i i i i i i i
i i
i i i
i i i i i i i i i i
i i
i i i
INPUT
A
OUTPUT
B
1
2
3
4
5
6
7
8
lockout
power
ethernet
network audio
push to solo | hold to mute
-9
-18
-24
-36
-48
-60
0
-9
-12
-18
-24
0
aux
mic
adjust
line
sig/clip
mute
sig/clip
mute
HEADPHONE
MICROFLEX WIRELESS
line
aux
Automatic Group Setup
An MXW Group can be associated without use of the control software when a network is comprised of only one Access Point Transceiver (APT), one
Networked Charging Station (NCS) and one Audio Network Interface (ANI). For best results, perform a factory default on the devices to clear any previous
Group associations.
1. Connect one APT, one NCS and one ANI to the network. The network must only contain one of each device.
2. Perform a factory reset on the devices (see the Factory Default section).
3. On the front panel of the ANI, press both input level selection buttons at the same time and hold for five seconds. The Channel Select LEDs will illuminate
green and the audio meter will flash to indicate that the association is successful.
Connecting the Microphone
to the Charger Slot
Summary of Contents for MICROFLEX MXW
