7
Group (G) and Channel (Ch)
A group is a set of compatible frequencies. A
single frequency within a group is a channel.
Navigate to the
F1
or
F2
group and channel
menus to make changes.
G:
Change the group
Ch:
Change the channel
Frequency
Navigate to the
F1
menu to edit frequency 1
or to the
F2
menu to edit frequency 2.
Use the
set
and arrow keys to change the
frequency in 25 kHz increments.
F2: ON or OFF
ON:
Frequency Diversity mode
OFF:
single carrier mode
Note:
This function is available in the
F2
:
frequency menu and the
F2
group and
channel menu.
Gain
Adjust the gain to set the input sensitivity
level. Gain range is -10 to +32 dB in 1 dB
steps.
Firmware
Displays the firmware version installed
in the transmitter
Device ID
The Device ID identifies the transmitter on a
network in WWB software or when Linked to
a receiver.
• ID length can be up to 8 characters
• Use arrow buttons to scroll through
characters
• Use
set
button to save and move to the
next character
AA Type
Sets the AA battery type (
Alkaline
,
NiMH
,
Lithium
) to ensure accurate battery metering
when using the optional AXT921 Battery
Carrier. The AA menu is only displayed when
the transmitter is powered by the carrier.
ShowLink Test
Activates the ShowLink test 5-bar display
to measure the remote control range of a
ShowLink Access Point.
• 5 bars indicate the center of the
coverage area
• 1 bar indicates the outer boundary of the
coverage area
• If bars are not displayed, ShowLink control
is not available
RF PWR
From the main menu screen, press and hold
the
set
button and the ▼ button to edit the
RF power level.
Use lower power settings to conserve battery
life and to prevent RF overload
at the receiver.
Note:
A password is required in
some regions.
PCB Serial Number
Use this menu to view the serial number of
the printed circuit board (
PCB
) installed in
the unit.
1. From the main menu screen, press and
hold the ▼ and “set” buttons to enter the
RF Power
screen.
2. Press the▲ button to access the serial
number.
3. Momentarily press the power button to
return to the home menu screen.
Troubleshooting
No ShowLink Alert
This alert appears when frequency is edited on a linked transmitter that
is beyond the range of an active ShowLink access point. Choose
OK
to
unlink the transmitter and complete the frequency change, or
Cancel
to
return to the home screen.
Input Overload
The
Input Overload
message indicates an excessive signal level
at the transmitter input. To prevent overload, reduce the gain setting.
Firmware Updates
Firmware is embedded software used to control features and the user interface. Periodically, new versions of firmware are available for download from
www.shure.com/wwb to incorporate additional features and enhancements. New versions of the firmware can be downloaded to AXT400 Receiver using
the Firmware Update Manager tool available in WWB6 software and installed on the transmitter using the infrared ports on the transmitter and receiver.
To access the AXT400 receiver firmware update menu:
Tx > IR Presets > FW Update
Parameter Menus
To adjust transmitter settings, use the arrow buttons to access and edit the parameter menus.
RF Mute
Disables or enables the RF carrier signal.
TX On:
RF signal enabled
TX Off:
RF signal disabled
Unlink
The
Unlink
command ends the Linking
relationship between a transmitter and a
receiver.
YES:
Ends the Link between a transmitter
and a receiver.
NO:
Preserves the Link between a transmitter
and a receiver.
Note:
When a transmitter is Unlinked, the
channel name will revert to
Unlinked
.
Deeply Discharged Batteries
Deep discharge occurs when a battery is discharged to less than 3.0
volts. The battery chargers have a Recovery mode designed to restore
charge to a deeply discharged battery.
When the charger detects a deeply discharged battery, it automatically
enters Recovery mode which supplies reduced current to the battery
for up to 30 minutes.
If recovery is successful, the charger will exit Recovery mode and
charge the battery to capacity. If the battery cannot be recharged,
charging stops and the battery must be replaced.
