ShopBot SBG00140 Page 9 Installation Manual Download | Manualshive

Page: 9 / 29

background image

Automatic Tool Changer (ATC) Installation Manual

●

July 23, 2018

© Copyright 2018 ShopBot Tools, Inc.

page 9

Plug the cables into the mating plug of the HSD spindle and
secure the socket head screw to lock the plugs in place.
Route the cabling from the spindle through the Y-axis E-
chain into the control box and over to the left side of the ATC
interface board.

Before locking cables into the Y-axis E-chain, manually
move the Z-axis to both of its extents of travel to make sure
there is enough slack in the cables for the Z-axis to move
freely.

Connect the small blue terminal block to the location marked
“VFD Logic”. Ensure the wires are attached with red
connected to S4, black connected to S1, and green
connected to SC.

The spindle sensor cable has a 12 pin male Wago connector
and will connect into the corresponding female piece on the
ATC board.

Find the female Wago connector on the board identified as
“spindle sensor cable.” Connect the male Wago connector
into the ATC interface board.

«
...
7
8
9
10
11
...
»

Summary of Contents for SBG00140






























Reviews:

No comments

Related manuals for SBG00140

Brand: ICS Schneider Messtechnik Pages: 124

Brand: Eaton Pages: 16

Brand: Eaton Pages: 6

Brand: Ecco Pages: 17

COOPER POWER SERIES

Brand: Eaton Pages: 8

Varycolor MICRO 150HTI

Brand: JB-Lighting Pages: 18

NI VISION PCI-8254R

Brand: National Instruments Pages: 13

NI VISION PCI-8254R

Brand: National Instruments Pages: 16

Brand: National Instruments Pages: 10

Brand: National Instruments Pages: 39

Brand: National Instruments Pages: 65

Brand: haacon Pages: 59

Brand: R&S Pages: 2677

Brand: Y.I.C. TECHNOLOGIES Pages: 6

Brand: MÄDLER Pages: 4

DependaBar DB-18-PCW

Brand: Healthcraft Pages: 13

Brand: Orliman Pages: 11

Aesculap S4 Cervical

Brand: B. Braun Pages: 43

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands