Assembly of 7x7 Cornershed
©
Thank you and congratulations on the purchase of your Shire Garden Building. We believe
that this product will give you many years of excellent service. This is a natural product
manufactured to a high standard therefore if you have any queries or experience any
difficulties then please contact our customer service hotline on
01945 465295
.
Preparation of Base
We recommend that the base onto which your building will stand should be at least
75mm larger in each direction than the total floor size of the building.
Actual floor area of the building: 2248 x 2248mm
Total height clearance: 2150mm
The chosen position in your garden for the siting of the building should be excavated to
a depth of 75mm to allow a base of sand, on to which paving slabs can be evenly laid -
THEY MUST BE LEVEL AND FIRM.
Treatment/Care of your Garden Building
Treat with a suitable decorative wood finish immediately. We recommend that all timber
pieces be treated again prior to assembly and again within 3 months of assembly. We
further recommend that all pieces are treated again at least annually or as frequently as
the instructions on the product used recommends.
We would suggest that all wall panels be treated in an upside-down position to allow the
finish/treatment to ingress into the tongue and groove jointing.
We would also remind you that you would rarely (if ever) be able to re-treat the
underside of the floor following assembly. We strongly recommend that the underside of
the floor is treated an absolute minimum of twice (not including pre-treatment).
Parts List
QTY DESCRIPTION
1
Roll felt 9 mtr long x 1 mtr wide
H
4
Coverstrips
I
2
Profiled coverstrips
I
4
Facia
J
1
Diamond
K
4
Window hinges
2
Casements stays
4
Casement stay pins
6
Door hinges
1
Padbolt
2
Bolts
67
60 mm screws
92
25 mm screws
8
10 mm screws
128
40 mm nails
150
13 mm felt nails
64
15 mm panel pins
Completed 7x7 Cornershed
Tools Required
●
Posidrive screwdriver (electric is best)
●
Drill, 6mm drill bit and 8mm drill bit
●
Hammer
●
Sandpaper (to smooth any rough edges)
●
Cutting knife
●
Tape measure
●
Step ladder
●
Ruler
●
Pencil
●
Saw
IMPORTANT!
PLEASE READ PRIOR TO ASSEMBLY OF
THE BUILDING
EVERY PRECAUTION IS TAKEN TO
ENSURE THAT YOUR BUILDING HAS NO
ELEMENT INCORRECTLY PLACED OR
POSSIBLY HAZARDOUS, HOWEVER
PRIOR TO USE PLEASE CHECK ALL
SURFACES FOR THE FOLLOWING:
1 RAISED GRAIN, SPLINTERS: sand
down timber to smooth finish
2 NAIL/SCREW/PIN HEADS PROUD: tap
home to be flush with surface of timber
3 DAMAGED SCREW HEADS
RESULTING IN SHARP SPLINTERS OF
METAL: replace
4 SHARP ENDS OF NAILS/ SCREWS/
PINS PROTRUDING THROUGH THE
PANEL: remove and reposition.
5 ENSURE ALL PARTS ARE SECURED
AGAINST REASONABLE FORCE:
remove and refit
6 ENSURE THERE ARE NO LOOSE
PARTS: remove and refit/discard
WE RECOMMEND THAT PROTECTIVE
GLOVES BE WORN THROUGHOUT
PLEASE LAY OUT PARTS AND CHECK OFF AGAINST
CHECK LIST BELOW:
QTY DESCRIPTION
2
Floor sections
A
4
Plain wall sections
B
1
Cornerpost square 1930 mm
B1
2
Cornerpost shaped
B2
1
Door aperture floor strip 1360 mm
B3
1
Door gable
B4
2
Window panels
C
2
Window frame inserts
C1
8
Panes Glazing material
C3
32
Beading
C4
2
Doors
D
3
Door stop strips
D2
1
Door cover strip
D3
4
Roof beam supports 715 mm
E1
1
Roof beam support block
(for back corner)
E2
1
Roof beams 2055 mm
F1
2
Roof beams 1490 mm
F2
2
Large triangle OSB roof sections
G1
2
Small triangle OSB roof sections
G2
4
Framework 1240mm Long
G3
2
Framework 2137mm Long
G4
Wood is a natural product and is therefore
prone to changes in appearance, including
some warping, movement and splitting,
particularly during unusual climatic conditions
(long hot or wet spells of weather). As a natural
occurrence this is not covered by a guarantee.
PLEASE NOTE
BUI
BUILT AROUND OUR REPUTATION
T AROUND OUR REPUTATION
D
B
B
A
K
J
E1
F2
F1
E1
E2
G3
G4
G4
G3
G3
H
G1
G1
G2
D2
D3
B3
B4
B1
C4
B2
C3
C1
B1
I
C
I
02/06
