background image

 

39 

 

(10) Oil Separator Filter Replacement 

 

Replace 

Every 1000 hours 

 

Remove the cover, and remove the O-ring and oil separator filter. 
Assemble a new O-ring to the cover and spread a thin layer of oil on the O-ring. 
Assemble a new oil separator filter and tighten the cover by hand. 

 
 
 
 
 
 
 
 
 

< NOTE > 

 Replace with a new O-ring each time the oil separator filter 

is replaced. 

 Oil separator filter part no. (with O-ring) 

1J419-05811 (Kubota part no.) 

 

11.  Long-Term Storage 

 

 

  WARNING : INJURY 

 

 Always be sure to stop the engine and remove the engine key when 

performing inspection or maintenance. 

 

 

 

  CAUTION : FIRE 

 

 Always be sure to wipe up any spilled fuel or oil. 
 Allow the generator to cool before covering with the protective cover. 

 

  CAUTION : BURNS 

 

 Do not touch the engine and surrounding components immediately after 

stopping the engine as they are still hot. 

 

(1)  Storage Procedures 

Perform the following maintenance procedures before storing this generator if it is not going 
to be used for two months or more. 

Remove the battery. 
(Refer to section “8-7. Checking the Battery Replacing the Battery”.) 
Replace the engine oil. 
(Refer to section “10. Inspection/Maintenance (1) Engine Oil Replacement”.) 
Drain the fuel from the fuel tank and filter. 
(Refer to section “10. Inspection/Maintenance (5) Fuel Filter Replacement (Main 
and Pre-Filters)
”.) 
(Refer to section “10. Inspection/Maintenance (6) Draining Water from the Fuel 
Tank
”.) 

 

Oil Separator 

Oil Separator 

Oil Separator 

Cover 

O-ring 

Loosen 

Tighten 

Filter 

 

 

 

 

Summary of Contents for DGM60MK

















































Reviews: