background image

 

25 

 

8-5.  Checking the Battery 

  CAUTION : EYE/SKIN INJURY 

 

 Wear rubber gloves and other protective wear to protect eyes, skin and 

clothing from the battery fluid which contains diluted sulfuric acid. If the 
battery fluid contacts eyes or skin, wash out immediately with a large amount 
of water. Be sure to receive medical treatment, especially if the fluid contacts 
the eyes. 

  CAUTION : EXPLOSION 

 

 Never use or recharge the battery if the fluid level is below the minimum level. 

 Do not create sparks or bring flame near the battery as it generates 

flammable gas. 

 

Check the fluid level, and add distilled water 

until it reaches the upper level when the fluid 
level is near the lower level.. 

Check the terminals for looseness and tighten 

properly. 

 

< Note > 

 It is necessary to recharge the battery when the specific gravity of the battery fluid is 1.23 or 

less. Request the authorized distributor where the generator was purchased to recharge the 
battery. 

 

  Replacing the Battery 

Remove the battery negative (-) cable. 

(Always be sure to remove the negative (-) 
side first.) 

Remove the battery hold-down clamp. 
Remove the battery positive (+) cable. 
Remove the battery. 

 

*  Install the battery by performing the above 

procedures in the reverse order. 
(First connect the positive (+) cable of the 
replaced battery.) 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Upper Level 

Lower Level 

 

(-) Post 

(

) Post 

Hold-Down 
Clamp 

 

Summary of Contents for DG25MK

















































Reviews: