BEDIENUNGSANLEITUNG
Lenkerendenblinker
SNAKE EYE
MOUNTING MANUAL
Handle bar indicator
SNAKE EYE
www.shin-yo.de
Mounting instructions and safety instructions for
SHIN YO handle bar indicator 202-550 and 202-552
SNAKE EYE
PLEASE READ THESE INSTRUCTIONS CAREFULLY BEFORE USE!
WARNINGS:
Electronic devices should be installed just by a qualified workshop! We advise you to check the correct function and
the correct fitting of the indicators before each ride. Just use 12V/21W Halogen bulbs, type H21W, BAY9S.
Attention:
Never touch the winker light and /or the bulb with pure skin or any material sensitive to heat,
while in use or short time after. The cables have to be laid with care that they can't get damaged while steering.
Danger of short-circuit!
HINTS:
Before you start with the installation, switch off the ignition, we recommend to disconnect the battery. The vehicle need a safe stand while mounting the winker lights.
Follow the general protection provision while mounting the indicators (wear protective clothing, etc.). These SHIN YO handle bar indicators are
homologated
for street
use in the EU. Unless you do not follow the mounting- and safety instructions and/or manipulate the product. Any kind of technical-manipulation to the cables and/or
connectors is prohibited. The winker lights are construed for a max. voltage of 12 V to 14,8 V DC, in case of a over voltage caused by damaged alternators, regulators
or damaged cables, you will loose any kind of warranty. We will not assume any responsibility for consequential damages.
MOUNTING INSTRUCTIONS:
specification of the enclosed parts:
picture 1
1 housing; 2 bulb socket; 3 bulb; 4 adapter w. flat part for wrench; 5 cable tube; 6 rubber spacer; 7 washer; 8 rubber tube; 9 earth contact; 10 nut;
11 connecting cable (positive pole).
step1:
Before you drill any hole, please read the instructions of your handle bar manufacturer and/or the regulations of your country. The required mounting
angle of the handle bar indicators is shown on
picture 2
.
Drill two small 3 mm holes for the cable exit into the handle bar underneath the switch units on each side of the handlebar. Alternatively you can also
drill one 4 mm hole in the middle position of your H/bar. Prepare the holes and make sure that no sharp edges can damage the cables. To prevent
intrusion of water, the drilled holes should face downwards and they should be sealed with silicone after you laid the cables.
step 2:
all relevant contact points (incl. inner side of the handle bar) should be cleaned from dirt, rust and grease.
step 3:
Choose the correct rubber tube
(8)
and assemble the parts in the correct order as shown on
picture 1.
Big rubber tube
(8)
, diameter 20 mm, for 1"
handle bar; middle rubber tube
(8),
diameter 17 mm, for 7/8" handle bar (mounted); small rubber tube
(8),
diameter 13 mm, for aluminium handle
bar; mini rubber tube
(8),
diameter 11,5 mm, for aluminium handle bar.
The cable tube
(5)
, the adapter
(4)
and the housing
(1)
must be fixed tightly. Squeeze the fitting rubber tube
(8)
with the nut
(10)
until the indicator
can be hardly pushed into the handle bar. Pull the cable
(11)
, with the help of a thin wire, towards the cable exit. Don't pull the cable too hard.
Put the indicator into the handle bar end. The housing of the winker light should be placed close to the handle bar with just a small gap. Turn the indi-
cator clockwise until the indicator is fixed and the amber lens is facing towards the driving direction.
Attention:
Do a maximum of 3 turns, otherwise
you have to squeeze the rubber tube
(8)
more tight before you put it into the handle bar. Make sure the throttle grip still turns forward and backward
easily. Now connect the
SHIN YO
indicator from the right side with the positive cable of the original wire harness (also from the right side). Do the
accordingly on the left side. The earth connection is provided by the contacts
(9)
and the handle bar. If the handlebar is made of insulating material
like aluminium, you have to lay an extra earth cable. The best position to connect this cable is between the rubber tube
(8)
and the nut
(10)
. Then
connect it to the earth wire of your vehicle.
step 4:
Place your vehicle on a plain ground and face it straight towards a wall. The vehicle and the handle bar must be straight. Don't sit on the vehicle or lift
it on the main stand. Now measure the distance between the ground and the middle of the lens. Right and left side must be the same distance. Mark a
line with the same distance on the wall and turn the indicator until the centre of the illuminated area is in the middle of this line. That means that the
illuminated area under and above the line must have the same size. You have to check this adjustment from time to time. The original front indicators
have to be removed now.
CHANGING THE BULB:
Attention:
Never touch the indicator and /or the bulb with pure skin or any material sensitive to heat, while in use or short time after. Wait until it cooled down.
step 1:
Turn the indicator anticlockwise unless you can pull it out of the handle bar.
Attention:
don't pull too hard, you can brake the cable or damage the
indicator. Unscrew the housing
(1)
from the adapter
(4).
Use a 10 mm fork wrench. Hold the housing
(1)
with the hole facing towards you, because
the bulb
(3)
and the bulb socket
(2)
are not fixed inside the housing and they can fall out. In case the bulb and the socket get stuck, turn the housing
and tap it on your palm.
step 2:
Insert the new bulb
(3)
without touching the glass cylinder with pure skin. Use a soft tissue. Place the small pins of the bulb to the corresponding groo-
ves of the socket
(2).
Two sides of the socket are flat and they fit exactly into the corresponding face of the housing
(1).
Insert the socket with the
bulb and screw on the adapter
(4).
To mount the winker light follow the steps as described before in this instruction sheet.
BEDIENUNGSANLEITUNG
Lenkerendenblinker
SNAKE EYE
MOUNTING MANUAL
Handle bar indicator
SNAKE EYE
www.shin-yo.de
HOMOLOGA
TED
