Shimano PD-MX80 Dealer'S Manual Download Page 3

3

IMPORTANT NOTICE

IMPORTANT NOTICE

 

This dealer’s manual is intended primarily for use by professional bicycle mechanics. 

Users who are not professionally trained for bicycle assembly should not attempt to install the components themselves using the dealer’s manuals. 
If any part of the information on the manual is unclear to you, do not proceed with the installation. Instead, contact your place of purchase or a local 
bicycle dealer for their assistance.

 

• Make sure to read all instruction manuals included with the product.

 

• Do not disassemble or modify the product other than as stated in the information contained in this dealer’s manual.

 

• All manuals and technical documents are accessible online at https://si.shimano.com.

 

• For consumers who do not have easy access to the internet, please contact a SHIMANO distributor or any of the SHIMANO offices to obtain a hardcopy 

of the User's Manual.

 

• Please observe the appropriate rules and regulations of the country, state or region in which you conduct your business as a dealer.

For safety, be sure to read this dealer's manual thoroughly before use, and follow it for correct use.

The following instructions must be observed at all times in order to prevent personal injury and physical damage to equipment and surroundings.
The instructions are classified according to the degree of danger or damage which may occur if the product is used incorrectly.

DANGER

Failure to follow the instructions will result in death or serious injury.

WARNING

Failure to follow the instructions could result in death or serious injury.

CAUTION

Failure to follow the instructions could cause personal injury or physical damage to equipment and surroundings.

Summary of Contents for PD-MX80




















Reviews: