background image

2

IMPORTANT NOTICE

 

Contact the place of purchase or a distributor for 
information on installation, adjustment, and replacement 
of the products which are not found in the user's manual. 
The dealer's manual for professional bicycle mechanics is 
available from our website 
(https://si.shimano.com).

 

Please observe the appropriate rules and regulations of 
the country, state or region in which you conduct your 
business as a dealer.

For safety, be sure to read this “user's 
manual” thoroughly before use, follow it 
for correct use, and store it so that it can 
be referenced at any time.

The following instructions must be observed at all times in 
order to prevent personal injury and physical damage to 
equipment and surroundings. The instructions are classified 
according to the degree of danger or damage which may 
occur if the product is used incorrectly.

DANGER

Failure to follow the instructions will result in death or 
serious injury.

WARNING

Failure to follow the instructions could result in death or 
serious injury.

CAUTION

Failure to follow the instructions could cause personal 
injury or physical damage to equipment and surroundings.

Important safety information

WARNING

 

Do not disassemble or modify the product. This may 
cause the product to not operate correctly, and you may 
suddenly fall and be seriously injured.

Riding precautions

 

Do not to pay excessive attention to the cycle computer 
display while riding.  
Doing so may result in an accident.

 

Confirm that the light works before riding.

Safety precautions

 

Be sure to remove the battery and charging cable before 
wiring or attaching parts to the bicycle.  
Failure to do so may cause an electric shock.

 

Be sure to follow the instructions provided in the 
manuals when installing the product.  
It is recommended to use SHIMANO genuine parts only. If 
bolts and nuts become loose or the product is damaged, 
the bicycle may suddenly fall over, resulting in a serious 
injury.

 

Do not leave this product in an extremely high 
temperature surrounding environment such as in a closed 
vehicle on a hot day, or near a heater. That can result in 
an explosion of the incorporated battery or the leakage 
of flammable liquid or gas from it.

 

Do not subject this product to extremely low air pressure. 
That can result in an explosion of the incorporated 
battery or the leakage of flammable liquid or gas from it. 
Transporting this product by air is not a problem.

Disposal precautions

 

Observe all federal, state and local environmental 
regulations when disposing of this product, because it 
incorporates a battery. Disposal of this product into fire 
or a hot oven, or mechanically crushing or cutting it can 
result in an explosion of the incorporated battery.

CAUTION

Riding precautions

 

Observe the instructions in the manual for the bicycle in 
order to ride safely.

Safety precautions

 

Never modify the system.  
Doing so may cause a system error.

 

Use the product under the supervision of someone 
responsible for safety, and only as instructed.  
Do not allow anyone (including children) with reduced 
physical, sensual, or mental capacity, or those without 
experience or knowledge, to use the product.

 

Do not allow children to play near the product.

NOTICE

Safety precautions

 

If any malfunction or trouble occurs, consult the place of 
purchase nearest you.

 

Be sure to attach caps to any unused connectors.

Summary of Contents for E5003




















Reviews: