Shihlin SA3 Series, User Manual

Page: 85 / 423

System parameter group 00
PARAMETER DESCRIPTION 83
5.1.2 Parameter restoration

Set parameters back to default.
Parameter Name Default Setting Range Content
00-02
P.996
～
P.999
Parameter restoration 0
0 Off
1 Clear alarm history (P.996=1)
2 Reset inverter (P.997=1)
3 Restore all parameters to default (P.998=1)
4 Restore some parameters to default 1 (P.999=1)
5 Restore some parameters to default 2 (P.999=2)
6 Restore some parameters to default 3 (P.999=3)
Parameter restoration

1: When 00-02(P.996～P.999) is set to 1, screen will flash , the alarm record will be erased after writing,
and 00-02 is reset to 0.

2: When 00-02(P.996～P.999) is set to 1, screen will flash and inverter will be reset, then 00-02(P.996～
P.999) is reset to 0. After resetting the inverter, the accumulated values in “electronic thermal relay” and “IGBT
module thermal relay” will be set to zero.

3: When 00-02(P.996～P.999) is set to 3, screen will flash , all the parameters will be restored to the
default values except the parameters in table 1 below. After parameters are restored, 00-02(P.996～P.999) is
reset to 0.

Exception The parameters in table 1 below will not be restored to the default values:
Group No. Name Group No. Name
00-00 P.90
Inverter model
06-55 P.751
E12
00-01 P.188
Firmware version
06-56 P.752
Output frequency during E1 alarm
00-23 P.186 Motor types selection 06-57 P.753
Output current during E1 alarm
00-24 P.189 50Hz/60Hz switch selection 06-58 P.754
Output voltage during E1 alarm
01-08 P.21
Acceleration/deceleration time increments
06-59 P.755
Temperature rising accumulation rate during E1
alarm
06-27 P.292
Total inverter operation time (minutes)
06-60 P.756
PN voltage during E1 alarm
06-28 P.293 Total inverter operation time (days) 06-61 P.757
Total inverter operation time during E1 alarm
06-29 P.296
Total inverter power on time (minutes)
06-62 P.758
Inverter operation status code during E1 alarm
06-30 P.297 Total inverter power on time (days) 06-63 P.759
E1 alarm date (years / months)
06-31 P.298 Output power (low 16 position) 06-64 P.760
E1 alarm date (days/hours)
06-32 P.299 Output power(high 16 position) 06-65 P.761
E1 alarm date (minutes / seconds)
06-44 P.740
E1
06-70 P.766
Output frequency during E2 alarm
06-45 P.741 E2 06-71 P.767 Output current during E2 alarm
06-46 P.742
E3
06-72 P.768
Output voltage during E2 alarm
06-47 P.743
E4
06-73 P.769
Temperature rising accumulation rate during E2
alarm
06-48 P.744
E5
06-74 P.770
PN voltage during E2 alarm
06-49 P.745 E6 06-75 P.771 Total inverter operation time during E2 alarm
06-50 P.746
E7
06-76 P.772
Inverter operation status code during E2 alarm
06-51 P.747
E8
06-77 P.773
E2 alarm date (years / months)
06-52 P.748 E9 06-78 P.774 E2 alarm date (days/hours)
06-53 P.749
E10
06-79 P.775
E2 alarm date (minutes / seconds)
06-54 P.750
E11
07-44 P.829 Version of EP301 communication card
Setting