background image

 6

 •

Charged by DC adaptor (Cigarette charger) while 

driving

 Plug the DC adaptor into Jump starter's charging 

port;

 Connect the DC adaptor to the vehicle’s cigarette 

outlet, LCD displays <CHARGING>;

 LCD displays <CHARGING IS COMPLETED> when 

the internal battery fully charged, Jump Starter will 

stop charging circuit automatically;

 Disconnect the DC adaptor from the cigarette outlet, 

and then unplug the DC adaptor from the Jump Starter.

Charged by AC charger

 Plug the AC adaptor into Jump starter's charging 

port;

 Connect the AC adaptor to a 100~240VAC electrical 

wall outlet, LCD displays <CHARGING>;

 LCD displays <CHARGING IS COMPLETED> when 

the internal battery fully charged, Jump Starter will 

stop charging circuit automatically;

 Disconnect the AC adaptor from the AC outlet, and 

then unplug the AC adaptor from the Jump Starter.

NOTE

 Please wait for 10 min if several fail attempts, then start the vehicle again. 

  If  the  vehicle  couldn’t  be  started  within  5S,  let  the  Jump  Starter  cool  for  3 

mins before attempting to start the vehicle again, or  you may damage the Jump 
Starter. 

 If the ambiance temperature is below -10

, the cranking performance will 

decrease sharply, the Jump Starter may not start the vehicle successfully. You 
can  try  a  few  attempts  to  start  for  warm  up  the  battery  and  then  increase  the 

starting performance. 

 If not successful, place the Jump Starter in a warmer area for a short time.

3.2 USING USB DC 5V OUTLET

The Jump Starter is a DC power source for all DC devices that are equipped 
with a USB plug.
1. Press 

the <POWER> button to turn on the Jump Starter.

2

.

P

 

lug

 

the

 

USB

 

switch cable

 

into

 

the

 

USB

 

Outlet

.

3

.

P

 

lug

 

the other

 

end

 (

Micro

 

USB) of the cable into your device

 

or

 

use

 

the

 

original

 

charging

 

cable

 

of

 

your

 

device. Turn device on, if necessary.

4

.

W

 

hen

 

finished

turn

 

off

 

the

 

device

 (

if

 

necessary

and

 

unplug

 

the

 

device

5. Press the <POWER> for 3S to turn off the unit or wait for 2 mins then the 
Jump Starter will shut down automatically.
6

.

R

 

echarge

 

the

 

Jump Starter immediately after unplugging the device.

3.3 USING DC 12V8A OUTLET

The Jump Starter is also a DC power source for all DC devices that are 
equipped with a Cigarette plug.
1. Make sure the device to be powered is OFF before inserting the Cigarette 
plug into the Cigarette outlet.

2. Press <POWER> button to turn on the Jump Starter.
3. Plug the Cigarette outlet cable into the Jump Starter’s 12V outlet.
4. Plug your device into Cigarette outlet and turn on the device (if required).

5. When finished, turn off the device (if required) and disconnect the device.
6. Press the <POWER> button for 3S to turn off the Jump Starter or wait for 2 
mins then the Jump Starter will shut down automatically. 

7. Recharge the Jump Starter immediately after unplugging the device.

NOTE: 

The Maximum output power of  the 5V and12V is 120W totally, the 

socket output will shut down automatically if the power of the device is over 
120W.
Electrical devices must be removed first, or the Jump Starter can not shut down 

automatically.

3.4 USING HIGH POWER LIGHT

1. Press <POWER> button  to turn on the Jump Starter.

2. Quick press <LIGHT> button to switch three different LED light modes. 
First: Highlight; Second: strobe; Third: SOS; Fourth: Off
3. Press <POWER> for 3S to turn off the Jump Starter.

MODEL: H

JEF10000-12

HJEF12000-12

                HJEF16000-12

                HJEF20000-12

READ THE INSTRUCTION MANUAL COMPLETELY BEFORE USING THIS PRODUCT.
RETAIN THIS INSTRUCTION FOR FUTURE REFERENCE

2

7

8

9

10

3

4

5

6

11

1

Product Feature

1.Jump Starter

2. High Power LED Light

3.Jumpstart socket

4.High-strength rubber handle

5.USB DC 5V/2.1A Outlet

6.USB DC 5V/1.0A Outlet

7. DC12V/8A Outlet

8.15V/1A Input port

9.POWER button

10. LIGHT button

11.LCD display

12. Oxford bag

13. AC charger

14. DC adaptor (cigarette charger)

15. 

12V Switch Cable and Cigarette 

Outlet (optional)

16. 5V USB/Micro USB Connector 

(optional)

17. Cable and clamps with fuse

CONTENTS

1. WARNING

2. PRODUCT FEATURE

3. OPERATING INSTRUCTION

INSTRUCTION MANUAL

SMART LITHIUM

     SAFETY

GUARANTEED

LiFePO4

Lithium Jump Starter and DC Power Source

12

13

14

15

16

17

IMPORTANT! CHARGE IMMEDIATELY AFTER PURCHASE, AFTER EACH 

USE AND EVERY 6 MONTHS, ALWAYS KEEP THE INTERNAL BATTERY 

FULLY CHARGED.

PROBLEM

POSSIBLE CAUSE

REMEDIES

5. TROUBLESHOOTING

The vehicle can not be 

jumpstarted 

The device can not be 

powered 

Can not  turn on the Jump 

Starter 

1) Improper clamp 

connections

2) The internal battery 

capacity is too low

3) Too low outside 

temperature

1) Improper clamp 

connections

2) The switch cable and 

connectors are defective

3) The internal battery 

capacity is too low

4) The device of 12V to be 

powered is over 120W

The internal battery 

capacity is too low 

1) Check and make sure the connections are 

correct 

2) Change a new switch cable and connectors  

3) Check the internal battery capacity and 

recharge it if necessary

4) Make sure the device to be powered is not over 

120W

Check the internal battery capacity and recharge 

it if necessary

6. MAINTENANCE AND CARE

7. SPECIFICATION

 1

 •

 2

 •

 3

 •

 4

 •

 5

 •

Fuse Protection

Overcharge and 

Overdischarge Protection

Against-reverse Plug

 7

 •

30WH

 250A

500A

1.98 lbs/900g

300A

400A

600A

900A

2.65 lbs/1200g

2.20 lbs/1000g

500A

1200A

3.09 lbs/1400g

36WH

48WH

60WH

Nominal Capacity 

( C10 25cels)

Cranking Amps

Peak Amps

Weight

Battery type 

12V Lithium Iron Battery 

  

15V 1 A 

 and DC 

.0 AC charger

adaptor (Cigarette charger)

  

Charger

  

DC 12V 8.0A Outlet (With 120W overload protection)   

USB

 

DC 5V 2.1A  

USB

 

DC 5V 1.0A  

Model 

HJEF10000-12 

HJEF12000-12 

HJEF16000-12 

HJEF20000-12 

High Power LED Light (1W 90LM) 

 

10AWG

Total 23.07" (58.6cm)

10AWG

Total 23.07" (58.6cm)

8AWG

Total 50" (127cm)

8AWG

Total 50" (127cm)

8.8"

×5.5"×2.8" (

223mm*140mm*72mm)

Size and length of 

Jump Сable and Сlamps

Function

The dimension of 

Jump Starter

The working 

temperature

14 

~140 

 (-10

-60

1) Check and make sure the connections is 

correct 

2) Check the internal battery capacity and 

recharge it if necessary

3) Try starting serval times to 

warm up the battery 

and then the starting performance increase. 

 Do not attempt to disassemble, modify, knock and throw the product, please 

contact your local distributor if the product has any problem.

 Never place the Jump Starter directly above battery being jumped

 Keep out of reach of Children.

IMPORTANT! PLEASE READ THE INSTRUCTION MANUAL CAREFULLY, 

AND OPERATE CORRECTLY ACCORDING TO INSTRUCTION.

WARNING! NEVER ALLOW CLAMPS TO TOUCH TOGETHER OR CONTACT  

THE SAME PIECE OF METAL.

 Do not charge the Jump Starter in dangerous places, such as near fuel, near 

fire etc.

 Do not expose the Jump Starter to the sun, rain or snow.

 Do not place the Jump Starter in microwave oven, pressurized container or 

vacuum chamber.

 Do not charge the Jump Starter with non-standard charger, use only 

specified charger equipped with Jump Starter.

 Do not immerse the Jump Starter in water or rinse by water, no waterproof 

design.

 Do not operate the jump starter if it has received a sharp blow, been dropped 

or otherwise damaged in any way.

www.skyrichbattery.com

Power by: Global Power Central Inc

Add: San Gabriel, CA 91776 

Step 4:

After successfully starting, remove the jump cable 

from the Jump Starter.

Step 5:

Press <POWER> button for 3S to turn off, or wait for 30S 

then the Jump Starter will shut down automatically.

Step 6:

Disconnect Red and Black clamps from the battery 

terminals.

Recharge the Jump Starter as soon as possible after use.

Step 1:

Press the <POWER> button to turn on the Jump 

Starter.

LCD displays the internal battery status, It is 

recommended the battery capacity be over 60% for 

jumpstarting.

Step 3:

Start the vehicle (Turn off all electronic devices to ensure a 

successfully start.)

Step2:

Connect the red clamp to po) terminal and 

black clamp to negative(-)terminal

Plug the Jump cable into jumpstart socket.

LCD Display

13.4V

<POWER>

<POWER>

POWER

LIGHT

POWER

LIGHT

Please read this instruction manual completely 

before using this product. 

Retain this instruction sheet for future reference.

SHIDO Jumpstarters are distributed by DC AFAM NV, Belgium.

For more info about SHIDO lithium batteries, please visit www.shido-batteries.com

MODEL: EF16000-12

Summary of Contents for EF16000-12









Reviews: