background image

 

15 

 

3. Handling of pump (Operating method)

 

 

2. Sucking up the water 

 

(1) 

Set the throttle dial 

  to the “SUCTION” 

position. 

(2) 

Pull the water suction lever 

  toward 

you and operate the vacuum pump to 
suck up the water. 

 

When the pointer on the pressure 
gauge starts to move, return the 
water suction lever promptly. 

 
 
 

3. Discharging the water 

 

(1) 

Open  the  water  discharge  valve  lever 

 

gradually to “

O” position until it stops. 

 
 
 
 
 
 

 

Communicate with the person at the snout and discharge water 
adjusting the pressure with the throttle dial 

  depending on the 

situation of the fire site. 

 

Keep the pointer on the pressure gauge and compound gauge in the 
green range when discharging the water. 

 

(2) 

By inserting the search light plug into the receptacle, the lamp lights up.

 

 

 

     

 

 

 

Open and close the water discharge valve lever always after returning the 
engine speed to low speed. 

 

Hold the nozzle at the end positively and wear the back band before charging 
the water. 

 

It not, you may lose control of the nozzle at the end and be injured when water 
charging is started. 

 

     

 

 

 

Do not direct the nozzle to other people or do not peep into it. 

 

You may be sent flying by high pressure and injured. 

 
 
 
 

Caution

 

 

Caution

 

 

Summary of Contents for TF516MH-AB









































Reviews: