ShenZhen Yuejiang Technology Dobot Magician User Manual Download Page 6

Page: 6 / 153

Dobot Magician User Guide

Dobot Magician Homing Operation

Issue V1.9.0 (2020-07-23)

User Guide

Security Precautions

This topic describes the security precautions that should be noticed when using this product.

Please read this document carefully before using the robotic arm for the first time. This product need

to be carried out in an environment meeting design specifications, you cannot remold the product

without authorization, otherwise it could lead to product failure, and even personal injury, electric

shock, fire, etc. The installation personnel, operators, teaching personnel, and programmers of the

robotic arm must read this document carefully and use the robotic arm strictly according to the

regulations of this document strictly.

1.1 General Security

DANGER

Robotic arm is an electrical equipment. Non-professional technicians cannot modify the

wire, otherwise it is vulnerable to injury the device or the person.

The following security rules should be followed when using the robotic arm.



You should comply with local laws and regulations when operating the robotic arm. The

security precautions in this document are only supplemental to local laws and regulations.



The

DANGER

WARNING

, and

NOTICE

marks in this document are only

supplemental to the security precautions.



Please use the robotic arm in the specified environment scope. If not, exceeding the

specifications and load conditions will shorten the service life of the product even damage

the equipment.



Before operating and maintaining the robotic arm, the personnel responsible for the

installation, operation and maintenance must be trained to understand the various security

precautions and to master the correct methods of operation and maintenance.



Highly corrosive cleaning is not suited to cleaning the robotic arm. The anodized

components are not suitable for immersion cleaning.



People cannot repair and disassemble the robotic arm without professional training. If

there is a problem with the robotic arm, please contact Dobot technical support engineer

in time.



Please comply with the relevant laws to deal with the product which is scrapped, and

protect the environment.



There are small parts in the packing box, Please keep them away from children, to avoid

any accidents.



DO NOT let children play with the robotic arm alone. All processes need to be monitored

while running. After processes have finished, please turn off the equipment promptly.



DO NOT put hands into the workspace of the robotic arm while running, to avoid bruising

or pinching.



Be careful during the robotic arm carrying or installing. Please follow the instructions on

Summary of Contents for Dobot Magician


























































































































































Search results

Summary of Contents for Dobot Magician

Reviews:

Related manuals for Dobot Magician

Brands by name

Popular brands

ShenZhen Yuejiang Technology Dobot Magician, User Manual

Search results

Summary of Contents for Dobot Magician

Reviews:

Related manuals for Dobot Magician

Brands by name

Popular brands